W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE
8Pages

{{requestButtons}}

Catalog excerpts

W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 1

INFRATECH COMFORT INSTALLATION USE & CARE MANUAL ALL WEATHER W-SERIES AND WD-SERIES QUARTZ TUBE ELECTRIC INFRARED RADIANT HEATER TABLE OF CONTENTS Warnings 2 Replacement Element Installation 5 Heater Coverage Areas 6 SAVE THIS MANUAL FOR FUTURE REFERENCE MADE IN USA

Open the catalog to page 1
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 2

WARNINGS READ ALL INSTRUCTIONS BEFORE USING HEATER Unit may be a source of possible shock. NEVER attempt to service heater without disconnecting its power source. Source of possible ignition. CAUTION High Temperature, risk of fire, keep electrical cords, drapery, furnishings and other combustibles at least 3' (0.9m) from the front of heater and away from sides and rear. MOUNTING HEIGHT/CLEARANCES CLEARANCE FROM COMBUSTIBLES: MIN. 6" (15.2cm) CLEARANCE BEHIND HEATER MIN. 18" (45.7cm) FROM SIDES AND ENDS OF HEATER · or Wall-Mounting, do not install heater closer than 18" (45.7cm) from...

Open the catalog to page 2
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 3

INSTALLATION INSTRUCTIONS This heater must be permanently installed and hard wired by a licensed electrician in accordance with local electrical codes. Assembly procedure must be performed with no electrical power to unit. Step 1: Check UL/CUL/CE label on heater for proper voltage. Step 2: Follow supplied wiring instructions. (See wiring instructions below) Step 3: Heater must be mounted with reflector angled down. Step 4: ll electrical connections must be in compliance with the National Electric Code (NEC) and local codes for A outdoor wiring. Step 5: Use only wiring components UL/CUL/CE...

Open the catalog to page 3
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 4

MOUNTING INSTRUCTIONS These models may be chain or bracket mounted to any ceiling or horizontal surface. Installation must be such that 18" (45.7cm) minimum clearance is maintained around the heater on all four sides and 36" (91.4cm) directly in front. A minimum of 6" (15.24cm) of clearance provided by mounting brackets is required behind the plane of the face. Heater can be hung using chains or custom brackets. Heater must be level, but can be rotated around its horizontal axis. 6" (15.2cm) INSULATED HOUSING SWIVEL MOUNTING BRACKETS (CEILING OR WALL MOUNT) 9-3/8" (23.8cm) 5-3/8" (13.6cm)...

Open the catalog to page 4
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 5

REPLACEMENT ELEMENT INSTALLATION (VISIT INFRATECH-USA.COM FOR VIDEO INSTRUCTIONS] Disconnect the power at the breaker. Remove the grill by grasping it in the middle, flex grill up and lift it off. Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from end of element to remove the existing quartz tube. Carefully install the new element. Remove one nut from end of the new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut. Use a thin 11/32" wrench to hold inside nut. Nuts must make a tight...

Open the catalog to page 5
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 6

MODEL WATTS MOUNTING HEIGHT AVERAGE COLD PROTECTED MODEL WATTS MOUNTING HEIGHT AVERAGE COLD PROTECTED NOTE: Mounting height should not be less than 6' (1.8m) if the heater is labeled as UL Listed and 8' (2.4m) if the heater is labeled as CUL Listed. Indoor or well-protected environments will generally exceed average. Heaters can provide less than average coverage in extremely cold/windy conditions. • INFRATECH QUARTZ TUBE ELECTRIC HEATERS are furnished with wall/ceiling mount swivel brackets. These brackets may be discarded when the heater is hung with chains,...

Open the catalog to page 6
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 7

Heater does not glow • Check supply voltage to confirm it matches voltage of heating element. Low heat output • A 240V element connected to 110V or 208V will warm, but not glow orange or generate sufficient heat for typical applications (Matching your voltage is extremely important). If element is visibly orange, but there is insufficient heat, refer to the areas covered with respect to conditions and mounting heights. • Replace or clean dirty or non reflective reflectors. Heater does not work • Disconnect power and check element with an ohm meter for continuity. If there is any...

Open the catalog to page 7
W & WD-SERIES COMFORT HEAT APPLICATION/INSTALLATION GUIDE - 8

LIMITED PRODUCT WARRANTY Model #: Serial #: Purchased From: Thank you very much for purchasing a INFRATECH Quartz Tube Electric Heater. We have designed this heater to provide you and your family with many years of great outdoor experiences. Please fill in the Model and Serial number as well as date of purchase in the areas indicated above. Please save this information for future reference. To get the full and safe enjoyment of your electric heater please read your Owner’s Manual carefully and review the proper operating and safety instructions with any family members that may be using the...

Open the catalog to page 8

All Infratech catalogs and technical brochures