INSTALLATION GUIDE IdeaGarden

Product catalog summary

Installation Guide Overview
This document provides a comprehensive guide for installing IdeaGarden panels, detailing the required tools, assembly steps, material handling, and recommendations for use and handling.

Specifications and Required Items
The installation requires specific tools including a mounting adhesive gun, wood screws, screwdriver, contact glue gun, tape measure, 45º cutter for panel edges, cutter, metal ruler, and pencil.

Assembly Procedures

Assembly Method 1: Apply assembly glue on the panel and bond both surfaces together.
Assembly Method 2: Position the panel on the wall and secure it with wood screws using a screwdriver. Ensure the bonding surface is clean and allow time between placing vertically attached panels.

Material Handling

Measurement and Selection: Measure the installation area, select the panel, and mark a guideline.
Cutting Method: Use a metal ruler and cutter to make precise cuts, performing multiple passes if necessary.
Corner Cutting: Adjust the ruler and make cuts at a 45° angle on both sides of the line.
Panel Assembly: Glue the panel onto the wall following the described methods.

Recommendations for Use and Handling
These guidelines are general and may vary by project. Ideatec is not liable for injury or damage. Consult a specialist if needed.

General Characteristics
The natural moss used in the products may vary in hue and height, leading to dimensional tolerance. Contact Ideatec for more information.

Certificates
Ideatec products are certified under EN 29073-1, 2, 3, EN 13501-1:2018, ISO 11925-2:2010, and EN 13823:2010 for various safety and quality standards.

Delivery and Handling
Products are shipped in protective boxes. Use forklifts for transport and avoid stacking heavy materials on the products. Handle with care to prevent damage.

Environmental Conditions
Maintain temperatures between 18º to 25º and humidity between 40% to 60%. Avoid exposure to ultraviolet light.

Installation and Maintenance
Use appropriate glue and handle with gloves to prevent damage. If moss dries excessively, spray lightly with water.

Catalog excerpts

ideaGarden INSTALLATION GUIDE GUÍA DE INSTALACIÓN

Open the catalog to page 1

Wall/Ceiling Mounting system 1: Required items : IdeaGarden: Wood screws : Information: Steps for assembly 1 of IdeaGarden panels: 1: Assembly glue on panel. 2: Glue both surfaces together. Steps for assembly 2 of IdeaGarden panels: 1: Place the panel on the wall in the desired position. 2: Fix the panel with wood screws using a screwdriver. * Make sure that bonding surface is clean and free of any areas that may become detached. * Allow a few minutes in between the placement of vertically attached panels. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965...

Open the catalog to page 2

Required items : Tape measure : MATERIAL HANDLING 45º cutter for panel edge: i- Prepare the necessary tools. ii- Adjust the metal ruler over the marked line. iii- Press the metal ruler against the panel and make the cut by sliding the cutter over the metal ruler . iiii - Perform as many passes as necessary to make the cut. i- Measure the area where the panel will be placed. ii- Select the panel to be cut. iii- Mark a guide line on the panel. Cutter and metal ruler: 3 Cutting method for corners: i- Glue the panel onto the wall according to the mounting methods described above. i- Prepare the necessary...

Open the catalog to page 3

IdeaGarden RECOMMENDATIONS FOR USE AND HANDLING These instructions are general guidelines and may vary depending on the project. Ideatec Advanced Acoustic Solutions shall in no event be liable for inju ry or property damage. If in doubt, consult a specialised installer/builder before carrying out any structural work. If you have any questions or comments about this document, please do not hesitate to contact Ideatec Advanced Acoustic Solutions. Ideatec Advanced Acoust ic Solutions is certiﬁed with: EN 29073-1, 2 and 3 for laminar mass, thickness, tensile strength and elongation at break and EN...

Open the catalog to page 4

Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

Open the catalog to page 5

All Ideatec Advanced Acoustic Solutions catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list