ideawood INSTALLATION GUIDE

Wall: Required items: (*)(**) Idealux LT Panel Montage: Metal angle bracket 40.40 Hardware items required for installation Information: Steps to assemble IDEALUX -LT panels: 1: Anchoring of metal angle bracket to the desired surface by means of screws. (4 per panel ). It is important to rethink the points of each module prior to fixing. 2: Place the panel on the angle brackets. 3: Screw on the upper side of the profiled batten and anchor it to the angle bracket. 4: Fit the next module and screw as described in point 3. (*) Configuration of standard modules (1980x600mm) Other formats on request....

Wall: Required items: Montage: Fixing clip Assembly hardware items required for installation Information: Steps to assemble IDEALUX LR panels: 1: Attach the fixing clips to the wall surface with screws. (6 per panel). 2: Apply pressure on the panel to fix the clips. 3: Repeat the same steps with each panel connecting them until installation is finished. (*) 6 fixing clips for 1800mm standard modules. For other sizes, please ask. USAGE RECOMMENDATIONS: Staggered alignment is recommended. Gap between head’s panels should be 5-10 mm (min). Shadowgaps should be 20 mm (min). Pol. Ind. Santa Fe // Comuna...

Wall: Required items: (*)(**) Idealux LT Panel Hanging piece (***)5 Hardware items required for installation Information: Steps to assemble IDEALUX- T panels: 1: Position and level the angle bars on the perimeter sides of the surface to be covered. 2: Layout of fastening elements (threaded rods, "T" profiles and hanging pieces). 3: Attach the threaded rod to the hanging pi ece by means of a nut, then move it through the "T" profile until it reaches the previously determined position. 4: Fit the cross bar over the "T" profile structure. 5: Leave the panels evenly on the metal structure until installation...

Ceiling: Required items: Idealux LR panel Mounting system: Ceiling support Steps to assemble IDEALUX LR: 1: Lay out flixing points on the surface depending on the Idealux LT 2: Attach the flixing piece with crews to the ceiling. Afterwards, place the bar guide bracket on the ceiling support to the desired height and fix both parts with the pin placing it thorugh the common hole to the clamping piece. 3: Lay down the panel on the guide bar bracket. 4: Repeat the steps with the remaining panels until finishing installation. Once panel is supported by the four hangers, move it towards the next one in...

Ceiling: Required items: (*)(**) Idealux FL Panel Mounting system: Threaded Rod + Nut Hanging piece Hardware items required for installation Information: Steps to assemble Idealux FL panels: 1: Position and level the angle bars on perimeter sides of the surface to be covered. 2: Layout of fastening elements (threaded rods, "T" profiles and hanging pieces). 3: Attach the threaded rod to the hanging piece by means of a nut, then move it through the "T" profile until it reaches the previously determined position. 4: Fit the cross bar over the "T" profile structure. 5: Leave the panels evenly on the...

Wall: Required items: Mounting system 1: Mounting adhesive gun: Wood screws: Hardware items required for installation Mounting system 2: Information: Steps for assembly 1 of Idealux FL panels: 1: Assembly glue on panel. 2: Glue both surfaces together. 3: Repeat steps 1 and 2 on the next piece and fit it to the piece attached to the wall. Steps for assembly 2 of Idealux FL panels: 1: Place the panel on the wall in the desired position. 2: Fix the panel with wood screws using a screwdriver. 3: Fit the next piece with the piece fixed to the wall and repeat steps 1 and 2. (*) Configuration of standard...

Wall: Required items: OMEGA metal profile Acoustic black fleece Start/End piece Double groove fixing cleat el Assembly hardware items required for installation Information: Steps to assemble Slatst: 1: Attach the Omega metal profile to the wall surface with screws. 2: Screw up on the same waythe start/end piece on the first and last panel. 3: Attach the panel to the wall surface by coupling the fixing cleats and the profile. 4: Introduce and turn, with just a twist, the fixing cleat for tongue and groove inside the profiles and after each panel. Move the connecting MDF piece towards the panel. 5: Attach...

Ceiling: Required items: Mounting system: Perimeter Trim OMEGA metal profile Acoustic black fleece Double groove fixing cleat 6 Assembly hardware items required for installation For other installation systems, please ask Steps to assemble SLATS: 1: Put and level the perimeter trims ont the surface perimeter that needs to be covered. 2: Lay out T-Grid system (threaded rod, metal profiles and hanging pieces). 3: Screw Start/End piece on the back of the slat, just on the first and last slat. 4: Push the start towards the omega profile, so the Start/End clips are inserted on the profile. 5: Twist flixing...

Wall: Required items: Mounting system : D-wood Panel Omega Metal Profile Start/End Piece Fixing cleat for double groove Acoustic black fleece Assembly Hardware items required for installation Information: Steps to assemble D-Wood panels: 1: Attach the metal profile to the wall surface with screws. 2: Screw up on the same waythe start/end piece on the first and last panel. 3: Attach the panel to the wall surface by coupling the fixing cleats and the profile. 4: Introduce and turn, with just a twist, the fixing cleat for tongue and groove inside the profiles and after each panel. Move the connecting MDF...

Ceiling: Required items: D-wood Panel Mounting system: OMEGA Metal Profile Perimeter Trim Fixing cleat for double groove Acoustic black fleece 6 Assembly Hardware items required for installation For other installation systems, please ask Information: Steps to assemble D-WOOD panels: 1: Put and level the perimeter trim on the surface perimeter that needs to be covered. 2: Lay out T-Grid system (threaded rod, metal profiles..). 3: Attach the panel to the wall surface by coupling the fixing cleats and the profile. 4: Attach the panel to the metal profiles by coupling the start/end piece against the profile....