ideaperfo INSTALLATION GUIDE
11Pages

ideaperfo INSTALLATION GUIDE

Wall panels Mounting system: Items required OMEGA Metal Profile Ideaperfo Panel Start/End Piece Fixing cleat for tongue and groove Assembly Hardware items required for installation Information: Steps to assemble Ideaperfo panels: 1: Attach the metal profile to the wall surface with screws. 2: Screw up the clamping start/end piece on the same way on the first and last panel. 3: Attach the panel to the wall surface by coupling the fixing cleats and the profile. 4: Introduce and turn, with just a twist, the fixing cleat for tongue and groove inside the profiles and after each panel. Move the...

Wall panels Mounting system: Items required Ideaperfo Panel Wooden batten Fixing cleat for tongue and groove Assembly Hardware items required for installation Information: Steps to assemble Ideacustic panels on wooden battens 1: Attach the wooden batten to the wall surface with screws. 2: Introduce the panel to the wooden batten structure. 3: Put the fixing cleat on the panel’s tongue and groove side and screw. 4: Attach the next panel with another fixing cleat until completing the installation. Double groove Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34...

Ceiling : Mounting system: Items required Ideaperfo Panel Perimeter Trim Main Runner * Hanging piece Assembly hardware items required for installation Ask for other installation systems Steps to assemble IDEAPERFO pannels : 1: Put and level the perimeter trims on the surface perimeter that needs to be covered. 2: Lay out T-Grid system (threaded rod, Main Runners and hanging pieces). 3: Attach the threaded rod to the hanging piece with the nut and move it through the main runner untill reaching the determined position. 4: Join the cross tee to the main runners structure. 5: Leave the panels...

Ceiling : Mounting system: Items required Ideaperfo Panel Perimeter Trim Main Runner Hanging piece Assembly hardware items required for installation Ask for other installation systems Steps to assemble IDEAPERFO pannelss: 1: Put and level the perimeter trims on the surface perimeter that needs to be covered. 2: Lay out T-Grid system (threaded rod, Main Runners and hanging pieces). 3: Attach the threaded rod to the hanging piece with the nut and move it through the main runner untill reaching the determined position. 4: Join the cross bar to the main runners structure. 5: Leave the panels...

Wall curves solutions: Mounting system 1. Curve Omega Profile 2. Standard curved Omega profile 3. Curve with Flex panels Information: Steps to assamble IDEAPERFO panels : 1: Omega Curved Profile: place the curved profiles at the same level as the installed omega and screw them to the fixing cleat. (Panel installed vertically). 2: Flat Curved Profile: attach and screw part of the fixing cleat to the omega profile body. Then, attach the flat curved profile and screw it to the whole. (Panel installed vertically). 3: Curve with Flex panels: screw the metallique angle to the wall and MDF ribs. Install the...

Corners alternatives: Frame edge Miter joint Non-machined trims Interior corner Machined trims Outline 9090 Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // info@ideatec.es noise under control

ideaperfo How to join OMEGA pieces Information: Steps to assemble the OMEGA metal profiles: 1: Fit the fixing cleat to one of the OMEGA metal profiles. 2: Joint the OMEGA profile in the same way. 3: Screw each OMEGA profile to ensure a good support. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // info@ideatec.es

ideaperfo ideaperfo Example of installation of IDEAPERFO panels (600x600mm) on a 5.76m2 surface: Items required for ceiling installation by means of primary profile and cross bar: 1- IDEAPERFO panels 2- Primary profile 3- Cross bar 4- Threaded rod * 5- Nuts 6- Hanging piece For wall installation of IDEAPERFO (600x600mm), by means of Omega profiles, (in the specific case shown of 5.76m2, arranged in four columns and four rows of Ideatec product) the following hardware items* are required: Items required for ceiling installation by means of primary and secondary profile: 1- IDEAPERFO panels 2-...

ideaperfo IMPORTANT These instructions are general guidelines and may vary depending on the project. Ideatec Advanced Acoustic Solutions will not be in any case responsible for injuries or property damages. In case of doubt, consult a specialized installer or builder before doing any structural work. If you have any questions or comments about this product, please do not hesitate to contact Ideatec Advanced Acoustic Solutions. GENERAL PROPERTIES Wood may present differences and deviations with regard to colour, grain and structure which could not be considered as possible defects. Final...