ideaflow INSTALLATION GUIDE GUÍA DE INSTALACIÓ

ideaflow Items required: Ideaflow Panel and Abaraska Mounting system: Ideaflow Panel and Abaraska: Information: Steps to assemble IDEAFLOW Panel and Abaraska panels: 1: Mounting adhesive on the panel. 2: Glue both surfaces. Make sure that the bonding surface is clean and free of areas that could peel off. Allow a few minutes between the placement of vertical attachment panels. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

Ideaflow Tile Wall Items required: Mounting system: Ideaflow Tile: Tile back Information: Steps to assemble Ideaflow Tile panels: 1: Mounting adhesive on the panel. 2: Glue both surfaces. Make sure that the bonding surface is clean and free of areas that could peel off. Allow a few minutes between the placement of vertical attachment panels. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

ideaflow Ideaflow Tile and Rejilla Ceiling Items required: Mounting system: 2 Angle profile Hanging piece Hardware items required for installation Other installation systems on request Information: Steps to assemble IDEAFLOW Tile panels 1: Position and level the angle brackets on the perimeter of the surface to be covered. 2: Layout of the geometrical position of fastening elements (threaded rods, "T" profiles and hanging pieces). 3: Attach the threaded rod to the hanging piece by means of a nut, then move it through the "T" profile until it reaches the previously determined position. 4: Splice secondary...

ideaflow Required items: Ideaflow Hexagon Mounting system: Ideaflow Héxagon: 2 Ideaflow Hexagon Back Information: Steps to assemble Ideaflow Héxagon panels: 1: Assembly glue on panel. 2: Glue both surfaces together. * Make sure that bonding surface is clean and free of any areas that may become detached. * Allow a few minutes in between the placement of vertically attached panels. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // info@ide

Ideaflow LWCF y SWCF Ideaflow LWCF and SWCF: A. Fixing by means of magnets: Rear magnet A. Fixing by means of magnets Information: B. Mounting adhesive gun: Steps to assemble Ideaflow WCF panels: A. 1: Anchoring of the rear panels to the wall by means of screws. 2: Screw magnets to the back of the WCF panel. 3: Place magnet on the back to place the piece. B. 1: Assembly glue on the back of the WCF panel. 2: Glue the WCF panel onto the wall. * Make sure that bonding surface is clean and free of any areas that may become detached. * Allow a few minutes in between the placement of vertically attached...

ideaflow Ideaflow LWCF and SWCF Ceiling Mounting system: Ideaflow LWCF and SWCF: Slab anchor Wire rope Same distance on all cables ceiling slab Clamping hook Steps to assemble WCF panels: *Make a guide hole of approximately Ø2mm using a punch Recommended fixing points Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] 1. Anchoring of connecting piece to the slab by means of screws. 2. Attach the wire rope to the lower piece of slab anchor. 3. Screw the two above together. 4. Pass...

Ideaflow Bafle Required items: Mounting system: Ideaflow Bafle: ceiling slab Information: Steps to assemble Ideaflow Bafle modules: 1. Anchoring of the connecting piece to the slab by means of screws. 2. Attach the wire rope to the lower piece of slab anchor. 3. Screw the two above together. 4. Pass the opposite end of the wire rope through the top of the clamping hook. 5. Pass it through the side o pening. 6. Screw the eyebolt onto the Bafle panel. 7: Attach the hook and eyebolt. 8. Final position. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34...

ideaflow IdeaflowSeparador Colgante (Hanging Separator) Mounting system: Ideaflow Hanging Separator Module Same distance on all cables ceiling slab Hanging Separator Slab anchor Wire rope Clamping hook Information: Steps to assembl e Ideaflow Hanging Separatormodules: 1. 2. 3. 4. 5. 6. 7. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] Anchoring of connecting piece to the slab by means of screws. Attach the wire rope to the lower piece of slab anchor. Screw the two above together....

Ideaflow Viga Wall Montage: Required items: Ideaflow Viga: 2 Fixing by means of magnets: Rear magnet Screwdriver wall * Beam back Information: Steps to assemble IDEAFLOW Viga: 1: Anchoring of the rear panels to the wall by means of screws. 2: Screw magnets in the indicated places on the beam. 3: Place magnet on the back to place the piece. viga back Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

ideaflow Ceiling Ideaflow Viga (Beam) Required items: Ideaflow Viga: A. Fixing by means of magnets: Rear magnet viga *Back Beam A. Fixing by means of magnets B. Fixing by means of magnets to metal profile: Metal profile Information: Steps to assemble IDEAFLOW Viga: A. 1: Anchoring of rear panels to the wall by means of screws. 2: Screw magnets in the indicated places on the beam. B. 1: Screw magnets in the indicated places on the beam. 2: Place the beam on the secondary metal profile to position the piece. B. Fixing by means of magnets to metal profile *Back Beam 3: Place magnet on the back to place...

ideaflow Ideaflow Required items: Tape measure: MATERIAL HANDLING 45º cutter for panel edge: i- Prepare the necessary tools. ii- Adjust the metal ruler over the marked line. iii- Press the metal ruler against the panel and make the cut by sliding the cutter over the metal ruler . iiii - Perform as many passes as necessary to perform the cut. i- Measure the area where the panel will be placed. ii- Select the panel to be cut. iii- Mark a guide line on the panel. Cutter and metal ruler: 3 Cutting method for corners: i- Glue the panel onto the wall according to the mounting methods described above....