ideafabric INSTALLATION GUIDE

Wall: Mounting system: Items required: Ideatec IMPALING Clip FiberTex Panel Assembly hardware items required for installation Wall surface Recommended IMPALING fixing points Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] Steps to assemble FIBERTEX panels: 1. Fix the Imapling clips to the desired surface area by means of screws . 2. Press FIBERTEX downward at 45º angle onto impaling clips. *Before the installation, place the panel 20mm above the intended location of the IMPALING...

Ceiling Mounting system: Items required: Metal Cable Fibertex Panel Retaining Spring Screw Anchor Level all the cables at the same distance Concrete Slab Safe hook Assembly Hardware items required for installation 2/3 * Leave the retaining spring’s hook visible Recommended fixing points Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] Dimensions for standard Fibertex panels Other dimensions, please ask Steps to assemble FIBERTEX panels: 1: Fix the connecting piece to the concrete...

Wall: Mounting system: Required items: Ideafabric block board Ideafabric block Ideafabric block A. Fixing by means of a silicone gun Steps to assemble the BLOCK panels: 1: Contact glue on the panel. 2: Contact glue on the surface. 3: Glue both surfaces together. * Make sure that the bonding surface is clean and free of any areas that may become detached. * Allow a few minutes in between the placement of vertically attached panels. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]...

Wall: Required items: Fixing cleat Hardware items required for installation e fa c sur Information: Steps to assemble the BLOCK panels: 1: Anchoring of the fixing cleat to the wall by means of screws. 2: Screw the second piece onto the back of the BLOCK panel, in opposite position to the previous one. 3: Fit both surfaces together. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

Wall: Required items: Mounting system: Start-end clamping piece Hardware items required for installation Information: Steps to assemble the BLOCK panels : 1: Anchoring of Omega metal profile to the desired surface by means of screws. 2: Screw the start-end clamping piece onto each panel in a similar way. 3: Attach the panel to the surface by coupling the clamping piece and profile. 4: Attach next panel and fit it to the previous one. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]...

cilindro acústico acoustic cylinder Required items: Acoustic cylinder Same distance on all cables ceiling slab A. Clamping by means of twisted cable and hook Metal plug Wire rope ceiling slab Information: Steps for A installation of ACOUSTIC CYLINDERS: Clamping hook Slab anchor 1. Anchoring of connecting piece to the slab by means of screws. 2. Attach the wire rope to the lower piece of slab anchor. 3. Screw the two above together. 4. Pass the opposite end of the wire rope through the top of the clamping hook. 5. Pass it through the side opening. 6. Attach the hook to the threaded rod and fix...

Example of installation of IDEAFABRIC panels on a 1.44m2 surface area: 5 4 Support material Items required for ceiling installation: Items required for wall installation: For ceiling installation of IDEAFABRIC (in the specific case shown of 1.44m2, arranged in two columns and two rows of Ideafabric product, with type B dimensions (1200x600mm) the following hardware items* are required: For wall installation of IDEAFABRIC (in the specific case shown of 1.44m2, arranged in two columns and two rows of Ideafabric product, with type B dimensions (1200x600mm) the following hardware items* are required:...

ideafabric USE AND HANDLING RECOMMENDATIONS INSTALLATION IMPORTANT These instructions are general guidelines and may vary depending on the project. Ideatec Advanced Acoustic Solutions will not be in any case responsible for injuries or property damages. In case of doubt, consult a specialized installer or builder before doing any structural work. If you have any questions or comments about this product, please do not hesitate to contact Ideatec Advanced Acoustic Solutions. Ideatec Advanced Acoustic Solutions is certified with CE, FSC, PEFC, ISO 9001 and ISO 14001. Certified wood FSC & PEFC are...

Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) España T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] cilindro acústic