ideacustic INSTALLATION GUIDE

Wall panels Mounting system: Items required OMEGA Metal Profiles Ideacustic Panel Start/End Piece Assembly hardware items required for installation Information: Steps to assemble IDEACUSTIC panels on Omega Metal Profiles: ::: 1: Attach the metal profile to the wall surface with screws. 2: Screw up only, and on the same way, the start/end piece on the first and the last panel. 3: Attach the panel to the wall surface by coupling the fixing cleats and the profile. 4: Introduce and turn, with just a twist, the fixing cleat inside the profiles and after each panel. Move the connecting MDF piece towards the...

Wall panels Mounting system Items required: Wooden batten Ideacustic Panel Fixing cleat for tongue and grove Assembly hardware items required for installation Information: Steps to assemble IDEACUSTIC panels on wooden battens: 1: Attach the wooden batten to the wall surface with screws. 2: Put the panel on the wooden batten structure. 3: Put the fixing cleat on the tongue and groove side of the panel and screw. 4: Attache the next panel with another fixing cleat until intallation is finished. Double groove Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609...

Ceilings: Itemes required: Mounting system Perimeter trim Ideacustic Panel Omega Metal Profile Start/End Piece Fixing cleat for tongue and groove and groove system Threaded rod + Nut Thread rod Threaded rod Assembly hardware items required for installation Ask for other installation systems Information: Types of edges Steps to assamble IDEACUSTIC panels:: 1: Put and level the perimeter trims on the perimetre of the area that needs to be covered. 2: Set out the geometric situation of the fixing items (threaded rod, metal profiles...) 3: Screw the Start/End piece just on the frist and last panel....

Wall curves solutions: Mounting system: 1. Curve Omega Profile 2. Standard/curved Omega profile/ 3. Curve with Flex panels Information: Steps to assemble IDEACUSTIC panels: 1: Omega Curved Perfil: place the curved profiles at the same level as the installed omega and screw them to the fixing cleat. (Panel installed vertically) 2: Flat Curved Profile: attach and screw part of the fixing cleat to the omega profile body Then, attach the flat curved profile and screw it to the whole. (Panel installed vertically). 3: Curve with Flex panels: Screw the metallique angle to the wall and MDF ribs. Install the Flex...

Corners alternatives: Frame edge Miter joint Non-machined trims Interior corner Machined trims Outline 9090 Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] noise under control

Access panel solution Mounting system 1 Information: Steps to assemble IDEACUSTIC access panels: 1: Spot the access space. 2: Screw, upside down, omega profiles to the Ideacustic panel. Leave 50 mm more on each side. 3: Lay the panel on the assembled structure. **All the panel profiles will be squared. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected] noise under control

Access panel solutions for folding roof hatch Mounting system: 1 Application: Information: Steps to assemble IDEACUSTIC access panels: 1: OMEGA profiles where the roof hatch will be placed must have a 675mm gap between axes. 2: Place the roof hatch* . Consider the opening direction. Specify the direction to place finish product. 3: Screw the roof hatch to the OMEGA profiles. 4: Place remaining IDEACUSTIC** panels. Press hatch inwards until a “click” is heard. 5: Hold the hatch while opening until 90º down. * The roof hatch comes with Ideacustic product installed on it. ** Cut the tongue part of...

ideacustic How to join OMEGA pieces Information: Steps to assemble the OMEGA metal profiles: 1: Attach the fixing cleat to one of the OMEGA metal profiles. 2: Do the same with the other profile. 3: Screw each OMEGA profile to ensure a good support. Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]

ideacustic ideacustic Example of mounting IDEACUSTIC panels on an 11,66m2 surface: Suspended ceiling installation items: Wall panelling installation items: For the installation of IDEACUSTIC on the wall, by means of Omega profiles, it requires (in the specific case shown of 11,66m2, arranged in two columns and 15 rows of Ideatec product) of the following hardware items*: 1- IDEACUSTIC panel 2- Omega 3- Fixing piece 4- Start/End piece** 5- Biscuit For the installation of IDEACUSTIC on the ceiling by means of Omega profiles, it requires (in the specific case shown of 11,66m2, arranged in two columns...

USE AND HANDLING RECOMMENDATIONS IMPORTANT These instructions are general guidelines and may vary depending on the project. Ideatec Advanced Acoustic Solutions will not be in any case responsible for injuries or property damages. In case of doubt, consult a specialized installer or builder before doing any structural work. If you have any questions or comments about this product, please do not hesitate to contact Ideatec Advanced Acoustic Solutions. Ideatec Advanced Acoustic Solutions is certified with CE, FSC, PEFC, ISO 9001 and ISO 14001. Certified wood FSC & PEFC are subject to availability....

Pol. Ind. Santa Fe // Comuna di Carrara, 10 03660 Novelda (Alicante) Spain T. +34 965 609 046 // +34 965 609 162 // F. +34 965 609 163 www.ideatec.es // [email protected]