GEMU090 Pearl Self Contained Ice Machine
16Pages

Installation Manual GEMU090 Series Ice-O-Matic 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081430-01 / 17-3371-01 P tN b 9081430 01 17 3371 01

Ice-O-Matic Parts and Labor Domestic & International Limited Warranty Mile High Equipment LLC (the “Company”) warrants Ice-O-Matic brand ice machines, ice dispensers, remote condensers, water filters, and ice storage bins to the end customer against defects in material and factory workmanship for the following: Cube ice machines, compressed ice machines and remote condensers. - Thirty-six (36) months parts and labor Flake ice machines, GEMD Maker Dispensers, and GEMU Undercounter compressed ice machines - Twenty-four (24) months parts and labor CD model dispensers - Thirty-six (36) months...

GEMU090 Installation and Use Introduction This manual includes information for the installation, operation and maintenance of the GEMU090 residential ice machine. The GEMU090 was developed to offer fans of Ice-O-Matic’s Pearl Ice form the ability to have that ice in their homes. Previously pearl Ice was only available in commercial establishments, where it developed a strong following because of the chewable nature of the ice. This machine makes authentic pearl ice, using the same process as the larger commercial machines. Table of Contents Product Description: . . . . . . . . . . . . . . ....

GEMU090 Installation and Use Product Description: This ice machine is designed to be used indoors, in Water Quality a controlled environment or outdoors within certain limits. The water to the machine must be potable, or fit for human consumption. Beyond that, water supplies The GEMU090 is made up of two major systems: vary in the degree of mineral content. As this ice the ice making system and the ice storage system. machine makes ice, all the water that flows into the The ice making system is a continuous flow type machine is changed into ice. That includes any ice machine, it makes ice...

GEMU090 Installation and Use Cabinet Dimensions FLOOR DRAIN ACCESS HOLE 1/4" O.D. COPPER WATER INLET COMPRESSION FITTING PROVIDED LEFT SIDE SVC. ACCESS PANEL 11 5/8" DRAIN ACCESS - FLEXIBLE TUBING 3/8" I.D. PUMP MODEL (INCLUDED) 5/8" I.D. GRAVITY MODEL (NOT INCLUDED) Ice-O-Matic Ice Systems are designed and manufactured with the highest regard for safety and performance. They meet or exceed the standards of agencies like ETL. Ice-O-Matic assumes no liability or responsibility of any kind for products manufactured by Ice-O-Matic that have been altered in any way, including the use of any...

GEMU090 Installation and Use Location Recommendations: The machine can be built into a cabinet. It is an air cooled refrigeration system and so air flows in and out of it through the grill at the bottom front. The grill must not be blocked by any covering door or other obstruction. Drain Conversion: A gravity drain model can be converted to a drain pump model by installing a drain pump kit. The drain pump kit consists of a drain pump, wiring harness and associated tubing. The part number is KPU090. Installation Notes Built In Situations: If a finished floor is to be installed in the area...

The control panel is visible when the door is opened. It has three indicator lights and two switches. Ice Making Check Water Clean Reset Control Panel The model and serial number plate is located on the bottom of the control panel box. The Bin Light and Ice Level Sensor are also visible from that angle, as is the Ice Chute. Check Water Clean Reset Serial Plate Ice Level Control Sensor Serial Number Plate The Scoop Holder is located on the right side of the ice storage bin. The normal ice level is about level with the scoop holder. Scoop Holder

Door Swing The door can be attached to open with hinges on the left or right. Retain all screws for re-use. 6. Remove original bottom hinge. To change: 1. Remove top hinge pin from hinge. 7. Remove two plugs or screws from upper cabinet bracket. 8. Attach bottom hinge to upper cabinet bracket using the original screws. 9. Place the door on bottom hinge, tip up to slide under top hinge. 2. Tilt top of door away from cabinet and lift door off bottom hinge. 10. Insert hinge pin into top hinge and door. 11. Tighten hinge pin. 12. Replace screws or plugs into holes left by hinges. 13. Check...

GEMU090 Installation and Use Plumbing - Pump Model Drains Water Supply There are two types of ice machine models, one that drains by gravity and one that has an internal drain pump. The recommended water supply tubing is ¼ inch OD copper. Stainless steel flex or reinforced PCV tube may also be used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit. Drain Pump Model drain installation 1. Locate the coil of 3/8” ID plastic drain tubing secured to the back of the unit. 2. Route the plastic drain tube from...

GEMU090 Installation and Use Plumbing: Gravity Drain Model clamp. Leave the other end of the tube lying on the floor of the base pan until the unit is positioned over the floor drain. Caution: Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code. 1. Place the ice machine in front of the installation opening. Adjust leveling legs to the approximate height. 6. Route the drain tube. Either a) Insert...

GEMU090 Installation and Use Electrical and Start Up The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. Installation check list: 1. Has the unit been connected to the proper water supply? 2. Has the water supply been checked for leaks? 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit. 3. Has the unit been connected to a drain? 4. Has the drain been tested for flow and leaks? 2. Position the unit in the...