PROFESSIONAL INSTALLATION GUIDE GUIDE D’INSTALLATION PROFESSIONNELLE INCLUDED IN THIS BOX GETTING STARTED MOUNTING SPECIFICATIONS Tools needed to install Enhanced Air Cleaner ^ Standard screwdriver ^ Phillips screwdriver ^ Metal cutter Drill ^ Duct Sealant

GETTING STARTED What to Expect From Your Honeywell Media Air Cleaner Congratulations for selecting the Honeywell Media Air Cleaner for your home comfort system! The Honeywell Media Air Cleaner captures and removes a significant amount of the air-borne particles from the air circulated through the high-efficiency pleated media filter. The Media Air Cleaner easily mounts in any position within the return air duct of any gas, oil, and electric forced warm air furnaces and to compressor cooling up to 5 tons. Additionally, it requires no electrical connections or maintainence beyond periodic media...

20 DEGREE EXPANSION PER SIDE PER FITTING (4 IN. PER RUNNING FOOT [100 MM PER 300 LINEAR MM]) GETTING STARTED For most efficient air cleaning, spread airflow evenly across the face of the media. If the duct is a different size than the media air filter cabinet, gradual transitions are required. Follow these guidelines when fabricating: • Use gradual transitions to reduce air turbulence and increase efficiency. • Use no more than 20 degrees (about 4 in. per running ft. (100 mm per 300 linear mm)) of expansion on each side of a transition fitting. DUCT SIZE CHANGED GRADUALLY TO PREVENT TURBULENCE....

GETTING STARTED Important Installation Requirements Failure to comply with these requirements will result in voided warranty, improper installation, and service callbacks. Personal Safety • Wear safety glasses while installing the unit. • Do not cut into any air conditioning or electrical line. • Follow professional safety standards and all local codes for plumbing, electrical, and mechanical considerations. Before Mounting • Using the figure on the cover and the lists on the inside cover, make sure that you have all the components for your Honeywell Media Air Cleaner and the tools to install...

Choosing a Mounting Position The Media Air Cleaner mounts in any position within the return air duct, usually next to the furnace blower compartment, but the arrow on the cartridge must point in the same direction as the airflow. See Figs. 1-8 for proper location of the media air cleaner for a variety of furnace installations. NOTE: The media air cleaner cabinet is sturdy enough to easily support the weight of the furnace and evaporator coil. Fig. 1. Highboy furnace with side installation. Media air filter is mounted vertically where return enters side inlet of furnace. Fig 2. Highboy furnace,...

Fig. 4. Lowboy furnace, with media air cleaner mounted horizontally in return plenum just above furnace and opposite heating plenum. Fig. 5. Counterflow furnace, with media air cleaner mounted horizontally in return duct or plenum just above furnace. Fig. 6. Central fan installation, with media air cleaner mounted horizontally in central return duct. Fig. 7. Horizontal furnace, with media air filter mounted vertically in return duct near furnace. Fig. 8. Two or more media air cleaners used in a high capacity system. Honeywell Media Air Cleaner 68-0239EF—12

Mounting the Honeywell Media Air Cleaner The following procedure describes a typical side installation on an existing highboy furnace (Fig. 1). Alternate procedures are noted as appropriate. Other changes in installation procedures may be necessary to complete your installation. NOTE: Before starting the installation, remove and discard the existing furnace filter (if used). Thoroughly clean the blower compartment. If possible, power vacuum the ductwork to remove accumulated dust in an occupied home or remove construction dirt in a new home. The media air cleaner cannot remove dirt that has settled...

Visually check the installation and make sure that: • Airflow is in the direction of the arrow on the media air filter cartridge. • Turning vanes and transitions, if used, are properly installed. • Joints in sheetmetal between media air filter and furnace are sealed. • All sheetmetal connections are complete. • Original furnace filter has been removed and blower compartment is cleaned. When you have verified that checkout has been completed: • Replace any access doors removed during the Installation or Checkout. • Run the furnace or cooling system through one complete cycle to make sure the system...

F100 Specifications MERV Rating*: MERV 11 Static Pressure Drop: 0.23 (in. w.c.) at 500 FPM Efficiency Definition*: Small Particles: E1 = 0.3 to 1.0 microns = 32% Medium Particles: E2 = 1.0 to 3.0 microns = 72% F200 Specifications MERV Rating*: MERV 13 Static Pressure Drop: 0.3 (in. w.c.) at 500 FPM Efficiency Definition*: Small Particles: E1 = 0.3 to 1.0 microns = 63% Medium Particles: E2 = 1.0 to 3.0 microns = 91% Large Particles: Large Particles: E3 = 3.0 to 10.0 microns = 99% 2 AVAILABLE ONLY IN UNITED STATES. * Minimum Efficiency Reporting Value (Media Filters Only) * Efficiency ratings are...

Home and Building Technologies In the U.S.: Honeywell 715 Peachtree Street NE Atlanta, GA 30308 http://yourhome.honeyweii.com ® U.S. Registered Trademark. © 2017 Honeywell International Inc. 68-0239EF—12 M.S. Rev. 10-17 Printed in U.S.A.

PROFESSIONAL INSTALLATION GUIDE GUIDE D’INSTALLATION PROFESSIONNELLE INCLUS DANS LA BOITE POUR MONTAGE CARACTERISTIQUES COMMENCER TECHNIQUES Outils requis pour installer l’epurateur d’air ameliore Dimension de l’epurateur d’air (po.)

À propos de l’épurateur d’air à fibres de Honeywell POUR COMMENCER Félicitations pour votre choix de l’Épurateur d’air à fibres de Honeywell pour votre système de confort d’intérieur! L’Épurateur d’air à fibres de Honeywell capture et retire une quantité considérable de particules contenues dans l’air circulant par le filtre à fibres à plis haute efficacité. L’épurateur d’air à fibres se monte facilement dans toutes les positions dans la gaine d’air de retour de tout appareil de chauffage à gaz, mazout, électrique et air pulsé et les systèmes de refroidissement par compresseur jusqu’à 5 tonnes....