Catalogs >
HELVAR >
LL1x21-CC

LL1x21-CC
4Pages

Catalog excerpts

21 W 220-240 VO /50 - 60 Hz • Maximum 21 W load • PCB iset (patent pending) for setting the output current • Load output is basic isolated from the mains • Driver protection Class i • Suitable for Class i luminaires • Open & short circuit protection • Protected up to 4 kV power network fast transients EH[C€ VMains Characteristics Voltage range DC range starting voltage Mains current at full load Frequency THD at full power Leakage current to earth Tested surge protection Tested fast transient protection 198 VAC - 264 VAC withstands min 176 VAC (max. 1 hour) max 300 VAC (max. 1 hour) 176 VDC - 280 VDC > 190VDC 95 - 120 mA 0 / 50 Hz - 60 Hz < 15 % < 0.3 mA 1 kV L-N, 2 kV L-GND |IEC 61000-4-5) 4 kV (IEC 61000-4-4) Insulation between circuits & driver case Mains circuit - Output Basic isolated Mains & output - Driver case Basic insulation Load Output Output current (Iout) Accuracy Ripple Uout (max) (abnormal) Start time 300 mA / 350 mA (default) ± 5 % < 2 %*, at s 120 Hz *S Low frequency, LED load: Cree MX-3 LEDs or equivalent (total load dynamic resistance > 12 OS 100 V For more information how to use PCB Iset, please see the page 4. Helvar I Helvar Qy Ab, Keilaranta 5 FI-02150 Espoo, Finland. Data is subject to change without notice. www.helvar.com

Open the catalog to page 1

Driver performance Typical power factor, 300 mA Total output power (W) Total output power (W) Typical power factor, 350 mA Total output power (W) Total output power (W) Operating Conditions and Characteristics Highest allowed tc point temperature 80 °C Ambient temperature range –20 °C ... +50 °C Storage temperature range –40 °C ... +80 °C Maximum relative humidity No condensation Life time (90 % survival rate) 100 000 h, at tc = 70 °C 70 000 h, at tc = 75 °C 50 000 h, at tc = 80 °C Quantity of drivers per miniature circuit breaker 16 A Type C Based on Icont Based on inrush current Ipeak...

Open the catalog to page 2

in Helvar 0.5 mm2 - 1,5 mm2 Solid core and fine-stranded According to EN 60598 1 m Connections and Mechanical Data Wire size Wire type Wire insulation Maximum driver to LED wire length Weight IP rating Note: • Not suitable for load side switching operation Helvar I Helvar Qy Ab, Keilaranta 5 FI-02150 Espoo, Finland, Data is subject to change without notice. www.helvar.com

Open the catalog to page 3

Helvar Using the PCB Iset current selection 1] To configure the LL1x21-CC for 300 mA output, the pre-cut piece of PCB must be removed. The piece is Located next to input connector PE terminal, pLease see the illustration of PCB Iset piece in the Figure 1. 2] The recommended tool for removing the PCB Iset piece is sidecutting pliers, as seen in the Figure 2. 3] First cut the side of the PCB Iset piece following the pre-cut Line, as seen in the Figure 3. 4] Next, snap the PCB Iset piece off of the main PCB. 5] Remove the piece completely, as seen in Figure 4. 6] Take special attention, that -...

Open the catalog to page 4