LC1x30-E-DA
5Pages

LC1x30-E-DA 30 W Dimmable DALI LED driver • DALI dimmable LED driver, 1 - 100 % dimming range • Suitable for DC use • SELV output protection for safety and flexibility in luminaire design • Driver protection Class II • Suitable for Class I and Class II luminaires • For driving Class III (SELV) luminaires, optional strain reliefs available for independent use outside of luminaire (LC-SRA/LC1x30-SR or LC-SRA-LOOP for looping the input cables) Helvar Product code: 5502 ^^^C€EH[WFunctional Description • Selectable constant current output: 350 mA / 500 mA / 700 mA • Switch-Control funtionality for easy-to-use intensity control • NTC terminal for overtemperature protection • Helvar Driver Configurator Support • Power monitoring (real time), Running hour monitor (accumulative), Energy management (accumulative) *) Low frequency, LED load: Cree XP-G LEDs 80 V Mains Characteristics Voltage range DC range starting voltage Mains current at full load Frequency Stand-by power consumption THD at full power Tested surge protection Tested fast transient protection Insulation between circuits Mains circuit - SELV circuit DALI circuit - SELV circuit Mains circuit - DALI circuit Mains and output - Driver case Load Output (SELV <120 V) Output current (IOUT) Accuracy Ripple Uout (max) (abnormal) 198 VAC - 264 VAC Withstands max. 320 VAC (max. 1 hour) 176 VDC - 280 VDC > 190VDC 0.14 - 0.18 A 0 / 50 Hz - 60 Hz 0.3 W < 17 % 1 kV L-N, 2 kV L-GND (IEC 61000-4-5) 4 kV (IEC 61000-4-4) Double/reinforced insulation Double/reinforced insulation Basic insulation Double/reinforced insulation 350 mA / 500 mA / 700 mA ± 5 % < 2 %, at s 120 Hz Helvar | Helvar Qy Ab, Keilaranta 5 FI-02150 Espoo, Finland. Data is subject to change without notice. www.helvar.com

Note: Dimming between 1 % - 100 % possible across the whole operating window Driver performance Typical efficiency Typical power factor Total output power (W) Total output power (W) Operating Conditions and Characteristics Highest allowed tc point temperature Storage temperature range Maximum relative humidity Ambient temperature range* in independent use Life time (90 % survival rate) 100 000 h, at tc = 65 °C 70 000 h, at tc = 70 °C 50 000 h, at tc = 75°C *) For other than independent use, higher ta of the controlgear possible as long as highest allowed tc point temperature is not exceeded...

LC1x30-E-DA Connections and Mechanical Data Wire size 0.5 mm2 – 1.5 mm2 Wire type Solid core and fine-stranded Wire insulation According to EN 60598 Maximum driver to LED wire length 5 m (1 m with NTC) Weight 123 g NTC trigger point 8.2 kΩ IP rating IP20 Note: • Not suitable for load side switching operation. • Label may differ if the unit is preset to fixed current. • Gray label from revision U onwards Helvar | Helvar Oy Ab, Keilaranta 5 FI-02150 Espoo, Finland. Data is subject to change without notice. www.helvar.com

information and conformity -freedoiw m liqktunj LC1x30-E-DA LED driver is suited for built-in usage in Luminaires. With LC1x30-SR/LC-SRA/LC-SRA-LOOP strain reliefs, independent use is possible too. In order to have safe and reliable LED driver operation, the LED luminaires will need to comply with the relevant standards and regulations (e.g. IEC/EN 60598-1). The LED luminaire shall be designed to adequately protect the LED driver from dust, moisture and pollution. The luminaire manufacturer is responsible for the correct choice and installation of the LED drivers according to the...

Helvar Conformity & standards Label symbols General and safety requirements Double insulated control gear suitable for built-in use. Thermally controlled control gear, incorporating means of protection against overheating to prevent the case temperature under any conditions of use from exceeding 120 °C. Control gear suitable for direct mounting on normally flammable surfaces, with or without thermally insulating material. Normally flammable surfaces are defined to include building materials such as wood, and materials based on wood, of more than 2 mm thickness. DALI certified control gear....