LC1x25-DA 25 W Dimmable DALI LED d river SELV output protection for safety and flexibility in luminaires DALI control input, 1-100 % dimming range Suitable for use in emergency lighting applications Long lifetime up to 100 000 h Driver protection Class II Suitable for Class I and Class II luminaires For driving Class III (SELV) luminaires, optional strain reliefs available for independent use outside of luminaire (LC-SRA/LC1x30-SR or LC-SRA-LOOP for looping the input cables) Functional Description • Adjustable constant current output: 350 mA (default) to 700 mA • Current setting programmable by Helvar driver configurator, by DALI commands or by external resistors • Hybrid dimming technique for high quality light • Switch-Control funtionality for easy-to-use intensity control • Adaptive LED overload protection. Reduces output current if overload is detected • Full load recognition, open and short circuit protection • Multipurpose terminal Iset/NTC for current setting or over temperature protection • Constant Light Output (CLO) (default disabled) • Power consumption monitor (real time), Running hour monitor (accumulative), Energy management (accumulative) Mains Characteristics Voltage range DC range starting voltage Mains current at full load Frequency Stand-by power consumption THD at full power Tested surge protection Tested fast transient protection 198 VAC - 264 VAC Withstands max. 320 VAC (max. 1 hour) 176 VDC - 280 VDC > 190VDC 0.13 A - 0.14 A 0 / 50 Hz - 60 Hz < 0.45 W < 17 % 1 kV L-N, 2 kV L-GND (IEC 61000-4-5) 4 kV (IEC 61000-4-4) Double/reinforced insulation Double/reinforced insulation Basic insulation Double/reinforced insulation Insulation between circuits & driver case Mains circuit - SELV circuit DALI circuit - SELV circuit Mains circuit - DALI circuit Mains and output - Driver case Load Output (SELV <60 V) Output current (Iout) Accuracy Ripple Uout (max) (abnormal) EOF. (EL use) 350 mA (default) - 700 mA ± 5 % < 2 %* at s 120 Hz *) Low frequency, LED load: Cree XM-L LEDs 60 V > 0.98 x output current with AC supply 11From revision D onwards. In earlier revisions U , 20 V - 48 Vand K at full load 0.94. out 2)From revision D onwards. In earlier revisions U 20 V - 36 V and K at full load 0.97. out Helvar | Helvar Oy Ab, Keilaranta 5 FI-02150 Espoo, Finland. Data is subject to change without notice. www.helvar.com

Note: Dimming between 1 % - 100 % possible across the whole operating window Total output power (W) Operating Conditions and Characteristics Highest allowed tc point temperature Ambient temperature range1 in independent use Storage temperature range Maximum relative humidity Life time (90 % survival rate) j For other than independent use, higher t of the controlgear possible as long as highest allowed tc point temperature is not exceeded Helvar | Helvar Oy Ab, Keilaranta 5 FI-02150 Espoo, Finland. Data is subject to change without notice. www.helvar.com

| LC1x25-DAHybrid dimming technique per channel Dimming range/ch Helvar hybrid dimming products combines both Constant Current Reduction (CCR) amplitude dimming and Pulse Width Modulation (PWM) dimming. CCR is a very efficient technique for dimming the light output, especially on higher range. On lower range, the hybrid dimming products implement high-frequency PWM dimming according to the table above. CONVERSION TABLE FOR OTHER TYPES OF MINIATURE CIRCUIT BREAKER Type C MCB's are strongly recommended to use with LED lighting. Please see more details in "MCB information” document in each driver...

in Helvar 0.5 mm2 - 1.5 mm2 Solid core and fine-stranded According to EN 60598 5 m Connections and Mechanical Data Wire size Wire type Wire insulation Maximum driver to LED wire length Weight IP rating • Not suitable for load side switching operation • Label may differ if the unit is preset to fixed current • LC1x25-DA has Iset terminal, however it is compatible with LED-Iset resistor values according to the table below. The current setting values are adjusted according to the LEDset specification. The resistor value for each required output current can thus be calculated from the formula R [Q]...

Information and conformity -freedoiw m liqktunj LC1x25-DA LED driver is suited for built-in usage in Luminaires. In order to have safe and reliable LED driver operation, the LED luminaires wilt need to comply with the relevant standards and regulations (e.g. IEC/EN 60598-1). The LED luminaire shall be designed to adequately protect the LED driver from dust, moisture and pollution. The luminaire manufacturer is responsible for the correct choice and installation of the LED drivers according to the application and product datasheets. Operating conditions of the LED driver may never exceed the specifications...