TeboPrime Okoume
4Pages

DESCR IPTION Base board: Okoume throughout Plywood Faces: both sides with a white pre- paint coating system 110 / 110 μ Average density (IAW EN 323): 500 kg/m3 (+/- 10%) Bonding (IAW EN 314-2): class 3 Service (IAW EN 636): class 3 exterior conditions Formaldehyde release classification (IAW EN 13986): E1 Content of Pentachlorophenol (IAW EN 13986): PCP ≈ 0 ppm Wall cladding, facades, gables, barge boards, fascias, constructions in exposed exterior environments. Any exterior end-use where the plywood product is going to receive a paint application. 22 (11) Other sizes & thicknesses: on request Preservative treatments, fungicide & Insecticide, antitermite: optional on request Cutting & TG processing: optional on request Flat, on intermediate bearers, in an enclosed dry and ventilated building, clear of the ground. As far as storage on site is concerned, provision should be made to cover the panels with an opaque waterproof sheeting with the underside of the stacks clear of the ground. FURTHER PROCESSING & INSTALLATION Compliance with standard practice, with regulations and with health and safety rules should be maintained at all times. Cutting and machining in the workshop possible except laser technology. Compatibility with other paint coatings TeboPrime is pre-painted with a water based primer. We therefore strongly recommend to privilege the selection of water based acrylic type finishing paints because of proven compatibility factors. However previous tests should always been carried out to verify suitability and compatibility on a sample piece in co-ordination with the paint supplier. Non water based finishing type paints should be strictly submitted to previous compatibility tests on a sample piece to verify suitability and in co-ordination with the paint supplier. Production on Thébault’s sites in France PRODUCTION SITES Groupe THEBAULT 47, rue des Fontenelles - 79 460 MAGNE - France Tél : +33 (0)5 49 35 70 20 info@groupe-thebault.com Sizes, number of plies & packaging TeboPrime Okoume

TECHNICAL PROPERTIES Characteristic values (MPA) IAW EN 789 - 1058 for structural calculations IAW Eurocodes 10 Available on DOP Strength in: Tension (ft), Compression (fc), Panel shear (fv) and Planar shear(fr) Modulus of elasticity in: Tension (Et), Compression (Ec), Panel shear (Gv) and planar shear (Gr) Others characteristic values Uses Use in structural applications (IAW EN 13986, EN 636-3, EN 636-2, EN 636-1) Suitable for use as structural element in exterior conditions (service class 3), humid conditions (service class 2) and interior conditions (service class 1) Nail and screw...

TeboPrime Okoume SURFACE CHARACTERISTICS TeboPrime Okoume is a semi- finished surfaced with an UV -sealant and a water based primer. The sealant coat is tight whilst the primer remains soft and open to allow a good adhesion of the finishing coats. In a complete painting system final paint coats are those that give the final hardness to the surface finish. The adhesion performance of the priming coat can exclusively be evaluated in accordance with the following test method: SKH publication 05-01 (10-10-2005) - Determination of the adhesion of paint on wood. For further information regarding...

TeboPrime Okoume Assembly Nails and staples are not recommended due to possible damage to the surface of TeboPrime plywood. Screws are to be preferred because they have a high tensile strength. Always use stainless steel screws. Pre - drilling of screw holes in TeboPrime plywood with a diameter equal to the shank of the screw. Then use a countersink drill to countersink the screw head. Prefer dome - headed TORX screws in combination with a seal washer. These connectors are available in a variety of colours which can match with the selected final finish. Nailing by hand is not recommended...