solid floor cutout location 36-3/4" minimum from floor (Platform must be able to support cabinet load, weight of oven, and additional oven loads) cabinet width Suitable bracing ™ to support runners over centerline GE Profile Series21-5/8" in. Single Wallunit overlap is with Advantium Wall Oven Dimensions (in inches)and 30 Oven 1/2" but allow 5/8" clearance from top edge of cutout Advantium® Technology A = The of cabinet B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout Cabinet Installation (in inches) (Platform must be able to support ™ C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout ADVANTIUM WALL load, weight of oven, and cabinet OVEN/GE PROFILE SERIES COOKNote: Cabinets installed adjacent additional oven loads) ING TOWER DIMENSIONS AND CABINET INSTALLATION to wall ovens must have an adhesion spec of at least 194° F temperature rating. INFORMATION (IN INCHES) NOTE: Cabinets installed adjacent to wall ovens must have an adhesion spec of at least a 194°F temperature rating. NOTE: 2" minimum between cutouts when installed above warming drawer or single wall oven. INSTALLATION INFORMATION: Before installing, consult installation instructions packed with product for urrent c dimensional data. Cabinet width Junction box location (240-volt models only) A 3" MIN between cutouts recommended—2" MIN required Construct Solid Bottom solid floor MIN 3/8" Plywood Supported by 2 x 4 or 1 x 2 Runners, all Four Sides. (Each platform must be able to support cabinet load, weight of oven, and additional oven loads) Suitable bracing to support runners Cutout height and width per drawer requirements cabinet width 21-5/8" over centerline of cabinet A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutoutConduit 19" C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout (48-1/2" long) (Platform must be able to support cabinet 1" Min. weight of oven, and load, above toekick or adjust to oven loads) additionaloven installation height Cabinet width NOTE: Use of the accessory drawer will replace the bottom trim piece for applicable installations. Please see installation instructions for full details. Junction box location (240-volt models only) Construct Solid Bottom MIN. 3/8" Plywood Advantium Wall Oven Dimensions by 2 inches)and Supported (in x 4 Cabinet Installation (in inches) 2 Runners, or 1 x all Four Sides. C 25-1/4" Required (Platform must be Cutout width Note: Cabinets installed adjacent cutout location able to support cabinet to wall ovens must have an adhesion load, weight of oven, 36-3/4" spec of at least 194° F temperature rating. and additional minimum oven loads) from floor 21-1/2" To Back of Control NOTE: Advantium 240 volt models cannot be installed under 36 inches height. 2x4’s or equivalent solid floor Junction box location (240-volt models only) A cabinet width For answers to your Monogram, GE Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000. bracing 21-1/2" To backsupport to C of Control runners 21-5/8" between cutouts 3" MIN over centerline recommended—2" MIN required of cabinet (Platform must be able to support cabinet load, weight of oven, and Construct Solid Bottom additional oven loads) Plywood Supported by MIN 3/8" A = The unit overlap is 1/2" but allow 5 B = The unit overlap is 2-1/4" but allow Listed by C = The unit overlap is 1" but allow 1-1 Underwriters Laboratories 2 x 4 or 1 x 2 Runners, all Four Sides. (Each platform must be able to support cabinet load, weight of oven, and Specification Revised 10/20 additional oven loads) 4-3/16 Cabinet width Cutout height and width per

GE Profile™ Series 30 in. Single Wall Oven with Advantium® Technology PREPARATION WITH AN ACCESSORY DRAWER PREPARE THE OPENING: The Advantium 120V can be installed in combination with other Built-In appliances. Always follow each product's Installation Instructions to compete the installation. PREPARE THE OPENING (CONT.) When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium and the other appliance overlaps. SINGLE OVEN INSTALLATION: Order a 30" wide single oven cabinet or cut...

GE Profile™ Series 30 in. Single Wall Oven with Advantium® Technology FEATURES AND BENEFITS Speedcook oven (240) - Enjoy oven-quality results two to eight times faster than a conventional oven M ultiple cooking functions - Expand your cooking versatility with an all-in-one oven Halogen heat - Skip the preheating with nearly instantaneous halogen heat O ver 175 preprogrammed menu selections - Preprogrammed selections make meals easy C ustom recipe saver - Conveniently store cooking instructions for up to 30 different recipes Three-Speed, 300-CFM venting system Allows for use with JX2200/2201 storage...