LED Driver 150T
9Pages

Driver - self made LED fixtures - easy to use - low cost - dimming options - battery supply - CV supply Futuro Lighting man 2015 Rev.O

Specification: Topology: Buck Vcc = 4,5-60 V DC I LED = Adjustable see next page for setting options Build your own LED fixture Regulation / dimming: - typical 3% output accuracy - soft start capability (just adding cap to PWM in) - high speed PWM 20kHz max - analog 0,7 - 2,5 V - thermal foldback Switching freq: 1 MHz max Rsense ratio: 0,15 Ohm / 1 A Dimensions: 20 x 17 x 5,2 mm Weight: 1,8 g Over temperature protection Over current protection Note: if PWM is not connected max ILED generated Options: encapsulation, reverse protection, thermal foldback Futuro Lighting

LED current setting Efficiency (%) Efficiency (%) X - linked by soldering iron Note: Vin is limited to 55 V max for 0,32 A mode, for 0,59 and 0,82A Driver needs to be thermally connected to heatsink with LED module. Futuro Lighting resign

Thermal foldback Application Example Back side: LED driver Connecting back side of LED driver to fixture heatsink will protect LED fixture against overheating thus extending LED life time and provide safe fixture operation even for inappropriate installations. Thermal foldback is temperature of the module is set to ~80°C Front side: LED module thermal connection can be done by appropriate thermo conductive both side tape or glue. Line regulation LED count = 12x Ta=24°C, Rh=61% thermal connection heatsink Futuro Lighting

Analog Dimming example (local) Appropriate for local dimming (Potentiomter close to Driver) Dimming level (%) * soft start capacitor Potentiometer selection: LIN - linear for linear dimming change LOG - logarithmic change, more appropriate for human eye response Futuro Lighting

Analog Dimming example (remote) Appropriate for remote dimming (1-10V dimmer) Dimming level (%) M1 soft start capacitor Signal selection: LIN - linear for linear dimming change LOG - logarithmic change, more appropriate for human eye response Futuro Lighting

Specification: Supply voltage 30-60 V DC Power consumption: 1,2 W max Model: Custom for LED Driver 150 Output voltage 0,55 - 2,55 VDC Outut current: 20 mA / channel max Number of dimm steps: 250 Illumination: Front - Side Blue LED End of range indication: blink (Blue) Power-up fade-in duration: 30 sec Setting memory type: EEPROM Dimensions: 85 x 85 x 30 mm Futuro Lighting resign Note: Implemented non isolated buck driver may generate audiable noise, this is regular behaving

Available as bare PCB or end user product 3D model on request Sunset: Time: XX:YY P = 0-90% Dimm = 5-99 Others: - Reverse protection - >3 days clock backup Display: 2x16 lines Actual time, status, intensity, Menu Illuminated (white) Dimensions: 87x50x10 mm Futuro Lighting PWM frequency: 2000 Hz Resolution: 1000 steps Output: 5V / 10mA Output: CV, 4A max Application example Specification: Supply Voltage: 6-25 VDC Supply current: <15 mA Power consumption: 0,65 W max Clock source: RTC 24h Settings for sunset and sunrise: Start time XX:YY Intensity 0-100% Dimm time: 5-99 minutes Sunrise: Time:...

Just single push to adjust Application example Specification: Supply Voltage: 6-25 VDC Supply current: <5 mA Output: PWM / CV 4A max Dimm steps: 100 Dimming characteristic: Log Available as bare PCB 3D model on request Controll: ON / OFF - short touch (<2sec) Intensity decrease Touch and hold till reaching required intensity (initial status ON) Others: - Reverse protection - implemented soft fade in and fade out - illumination of touch button - built in N-MOS for CV LED strips Indicator status Inactive when off or during fade in and out Intensity increase Touch and hold till reaching...