FRAMED FORMWORK DESTIL MINI CASSERO A TELAIO DESTIL MINI

AVVERTENZE SULLA SICUREZZA SAFETY WARNINGS • The respect of these instructions does not exempt from compliance with all safety regulations in force in the country where you use the system. • These instructions are intended for users of TF products and systems. Each one must be aware of the contents of this manual; in case they have difficulties in reading the same, the employer has to provide education of the same • The User’s Manual instructions must always be available at the workplace for all operators • This manual, even if used in order to draw up a Method Statement, will not substitute...

ASSEMBLING INSTRUCTIONS 16 PANEL STRUTS 16 GAMMA DELLE DIMENSIONI 14 ANGOLI DI DISARMO RAPIDO 30

DESTIL FRAMED FORMWORK | CASSERO A TELAIO DESTIL FEATURES Destil Mini wall framed formwork is the new TF system which can be handled as handset and without crane, thanks to its reduced panel weight. DEStIL Mini offers TF systems usual efficiency and reduction of total costs, even with a reduced weight, through the following features: MODULARITY: a wall formwork with a wide modularity available in heights of 300 cm, 270 cm, 150 cm, and 120 cm and widths starting from 30cm and up to 90 with a 15cm span between panels. A choice for any necessity. STEEL: highly resisting Steel, S315M type C . Frame...

CASSERO A TELAI O D ESTI L MIN I Material: hot-rolled highly resisting steel S355MC, according to EN 10149 part 1/ part 2 and DIN EN 10051 Admissible load: Up to H 3m 60 kN/m2 Over H 3m 40 kN/m2 Finishing: Hot Dip galvanization Panel: birch multilayer panel, 15mm thick Materiale: Acciaio laminato a caldo ad alta resistenza S355MC, a grana fine, secondo EN 10149 parte1/parte2 e DIN EN 10051. Portata ammissibile: sino ad H 3m 60 kN/m2 oltre H 3m 40 kN/m2. Finitura: zincatura a caldo Pannello: multistrato di betulla spessore 15mm 1 Highly resistant steel frame, 92mm high, with perimeter concavity...

DESTIL MINI FRAMED FORMWORK | CASSERO A TELAIO DESTIL MINI - lightness - modularity - high compatibility with other formwork systems currently on the market - accessories gamme completeness - rapid formwork erection, dismantling and shifting on-site - respect of measure tolerances and great care in producing every system component - wide range of steel frame elements - pre-and post-selling assistance - attention and respect of safety factors - leggerezza - modularità - alta compatibilità con sistemi di casseratura di altri leader di mercato - completezza e intercambiabilità degli accessori -...

DESTIL MINI ELEMENT CONNECTION | COLLEGAMENTO DI ELEMENTI DESTIL MINI Scaffold Bracket cod. CC0022DM mensola di getto cod. CC0022DM Panel strut H=340 cod. CC0025DM Puntello di sostegno H=340 cod. CC0025DM Super plate nut cod. CC0045 Dado a piastra articolata cod. CC0045 Quick acting clamp cod. CC0008DM Morsa a cuneo cod. CC0008DM

DESTIL MINI FRAMED FORMWORK | CASSERO A TELAIO DESTIL MINI DESTIL MINI SCAFFOLD BRACKET | MENSOLA DI GETTO DESTIL MINI To be used for installation of walking platforms or service platforms combined with wooden or steel planks. The scaffold bracket is easily joined to the formwork panels through its fixing head. It is recommended to contain the distance between two scaffold brackets to no more than 1,8 meters. The walking platforms must have timber board at the bottom, the middle and top of the scaffold bracket post. The access to the walking platforms have to be guaranteed by suitable ladders....

PLATE NUT D15 (0150) | DADO A PIASTRA D15 (0150) Screwed on the tie rods in order to lock up bindings (2 plates needed for each bar). Admissible load =90 kN (according to regulation DIN 18216). Si avvita sulle barre di ancoraggio D15 per serrare le legature (n° 2 piastre per ogni barra). Portata ammessa a norma DIN 18216=90 kN. QUICK ACTING CLAMP | MORSA ACUNEO Connect the adjacent formwork elements together. It can be placed in any point of the frame's perimeter, preferably close to the stiffeners. Destil Mini Quick Acting Clamp and Destil Mini Multi Function Clamp: - align perfectly the elements...

DESTIL MINI FRAMED FORMWORK | CASSERO A TELAIO DESTIL MINI TIE ROD | BARRA DI ANCORAGGIO Used to fix corresponding formwork during the casting operations. Produced in standard length of 6 meters and cut to necessary length on the construction site. The bars can be reused after the works; but prior to casting, they should be put in plastic tube, type 22/26, and then can be reused. For correct usage the bar should be equipped with appropriate accessories (Super plate nuts or Hexagon nuts or Plate nuts D15). Admissible load: 90 kN (according to regulation DIN 18216) Ultimate load: 190 kN (according...

DESTIL MINI CLOSURE SOLUTIONS | COMPENSAZIONI ELEMENTI DESTIL MINI Multi function clamp cod. CC0009DM Morsa di compensazione cod. CC0009DM Super plate nut cod. CC0045 Dado a piastra articolata cod. CC0045 Universal waling cod. CC0011DM cod. CC0012DM Rotaia di fissaggio cod. CC0011DM cod. CC0012DM Universal fixing bolt for waling cod. CC0016DM Morsetti bloccaggio rotaia cod. CC0016DM

DESTIL MINI FRAMED FORMWORK | CASSERO A TELAIO DESTIL MINI CLOSURES UP TO 15 cm | COMPENSAZIONE FINO A 15 cm Wall compensation, from 0 to 15 cm, using wooden beam or wooden boards, multi function clamp for the connection of the elements and universal waling for alignment. Compensazioni da 0 a 15 cm con quadrotti o tavole di legno, morsa di compensazione per il collegamento dei moduli e la rotaia di fissaggio per l’allineamento. Wooden beam or boards Tavola o quadrotto in legno Universal waling Rotaia di fissaggio Multi function clamp Morsa di compensazione CLOSURES UP TO 50 cm | COMPENSAZIONE...

DESTIL MINI FRAME FORMWORK ELEMENT Logical modular system in steps of 15cm. The heights and the widths of the frame Destil Mini elements form a modular system logical and simple to use that makes the formwork particularly flexible and cost effective. - easy planning and forming - adjustment of the height and width in steps of 15 cm - few compensations required - clear positioning of junctions. - 5 element widths, - 4 element widths With this wide range you can form any geometry. ELEMENTI CASSERO A TELAIO DESTIL MINI Sistema modulare logico in passi di 15 cm. Le altezze e le lar-ghezze degli elementi...