installation guide
10Pages

RESIN ROOFING & WALL

RESIN ROOFING & WALL 1 Ridge Unit 3 Diagonal Ridge 5 Valley Gutter 7 Barge Board 2 3-way Ridge Piece 4 Terminal Ridge 6 Tile-end Synthetic resin roofing and wall cladding coated with ASA resin are special 3-layer co-extruded sheets. As the top layer material, ASA anti-climate engineering resin is extraordinarily suitable for outdoor use. Even exposed to ultra-violet radiation, dampness, heat, chillness and impact, the products remain the stability of color and physical properties. Tests held in Aging Test Center of Arizona and Florida by GE prove that A E is less than 5 within 10 years,...

RESIN ROOFING & WALL FANE xiNE AND INSTALLATION UNDERNEATH STRUCTURE I.Deck structure The surface of the deck should be smooth, the material of the deck should be of small deformation, the deck should be more than 12mm thick (according to the pulin span). A 3-5mm gap between two decks is essential for deformation. The waterproof rolls should be unrolled smoothly and vertically with accurate overlaps. The angles of steel structure should be precisely controlled during processing, which will influence the pitch of the roof. The deviation of angles will cause an uneven roof. All the steels...

RESIN ROOFING & WALL Zinc coated self-tapping screw Table Lengths for Roma Tile Table Lengths for Royal Tile 5 668 Standard Length for shipment by full cotainer 5.576 Standard Length for shipment by full cotainer 2.18 Standard Length for shipment by full cotainer 1.968 Standard Length for shipment by full cotaine Shandong Fangxing Building Materials Co., Ltd. RESIN ROOFING & WALL FANE XING AND INSTALLATION During handling, the products must not be thrown rudely to avoid damaging or scratching the product surface. For single sheet longer than 8m, enough supporting points are essential to...

RESIN ROOFING & WALL FANE XING AND INSTALLATION The remaining sheets cut at the beginning are not wasted as they can be used at the end of the roofing as adjustments. Complete the opposite side in the same way. Line up the vertical rows of tiles on the opposite side with those of the first, in order to assemble the ridge tile. Attention! For lower slope or in particularly windy or rainy zones it is appropriate to seal the overlap using the resin sealant or silicon RIDGE TILE The installation of ridge tile should begin from one side. For the first tile, it should be half cut to avoid the...

RESIN ROOFING & WALL CONNECTION WITH CHIMNEYS- Assemble the sheets from one side normally until they get close to the chimney. Cut the sheets around the chimney accordingly. Add extra purlins next to the chimney if necessary to fix roof sheets. Use synthetic resin or metal flashings, stick the flashing board to the wall and tiles by self-screws or nails and seal the higher end of flashing with silicon sealant. (See diagrams above) Flashings are recommended to be processed at site by metal board, as the roof pitches and position of chimneys are variable for different Aluminum or galvanized...

RESIN ROOFING & WALL TRAPEZOIDAL ROOFING SHEETS Ridge Unit Multi-functional ridge unit Shandong Fangxing Building Materials Co., Ltd. RESIN ROOFING & WALL WALL CLADDINGS Installation Guideline 1. Trapezoidal roofing sheets are applicable to roof pitches from 6°to 22°, with purlin span no more than 1200mm. 1105-T roof sheets are applicable to roof pitches from 18° to 22°,with purlin span no more than 800mm. Wall claddings are applicable to the interior and exterior wall of buildings, with purlin space no more than 1200mm. 2.Thermal insulating material can not be used directly under the...

RESIN ROOFING & WALL PHOTO GALLERIES Shandong Fangxing Building Materials Co., Ltd. Shandong Fangxing Building Materials Co., Ltd.