Installation manual e-MatriX
20Pages

Installation manual e-MatriX heat 800/500 I,II,III e-MatriX heat 800/650 I,II,III ENG

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriXheat 800/500-6501,II,III

2 = Brackets (2x) in-line filter A = EA backflow protection valve Mains water Installation manual e-MatriX heat 800/500-65

Installation manual e-MatriXheat 800/500-6501,II,III

1 Dear user Congratulations on your purchase of a Faber fire! A quality product from which you will experience warmth and atmosphere for many years. We recommend that you read this manual carefully before using the fireplace. If any problem arises despite our strict quality control, you can always contact your dealer or Glen Dimplex Benelux B.V. For any warranty claims, it is essential you first register your fireplace. During this registration, you'll find all information regarding our warranty. > Please note! The details of your fireplace can be found in the user manual. You can register...

Installation manual e-MatriXheat 800/500-6501,II,III 4.2 Placing the fire For a proper functioning of the fire, always ensure that the fire is levelled. Floor standing Place the fire in the correct position and fix it to the wall, see fig. 1.1. Hanging on the wall (fig. 1.2) The fire can be mounted on the wall using the optional wall bracket "A" (see also dimensional drawing in chapter 12.6). Use the distance holder "B" for vertical leveling. Remove the existing brackets, see fig. 1.1. 4.3 Installation and finishing (see fig. 1.0) With cover strip "A" Built the false chimney breast or...

Installation manual e-MatriXheat 800/500-6501,II,III 5.3 Side glass For cleaning only it's not necessary to remove the side glass. • First remove the front glass see chapter 5. • Place a suction cup and remove the side glass, see fig. 2.2. For replacing the front glass repeat the steps in reverse order. 6 Removing fuel bed > Please note! - Never lift up the fuel bed without using the supplied handles. - Keep these handles for future use. • Remove the front glass see chapter 5. • Cover the frame to avoid scratches see fig. 3.1-A. • Screw the handles in the fuel bed see fig. 3.0. • Lift up...

Installation manual e-MatriXheat 800/500-6501,II,III 1. Gently slide the air filter upwards out of its plastic holder, see fig. 8.0. 2. Gently rinse with water in the sink and dry with fabric towel before returning. 4. Place the fuel bed, see chapter 6. 5. Place the front glass, see section 5. Replacing transducers > Please note! Always press the mains switch of the Control box to the "OFF" (0) position (see fig. 4.0-D) and disconnect the power supply. 1. Follow the first 7 steps in section "Cleaning water sump" in chapter 9.1 to gain access and remove the transducers. 2. Place the new...

Installation manual e-MatriX heat 11 Troubleshooting and fault codes remote control

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriX heat 800/500-650 I,II,III

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriX heat 800/500-650 I,II,III 12.6 Wall brackets e-MatriX 800/500 I,II, III heat (Article number A9325196) e-MatriX 800/650 I, II, III heat (Article number A9324596)

Installation manual e-MatriXheat 800/500-6501,II,III 12.7 Remote access door (Article number A9299463)

Installation manual e-MatriXheat 800/500-6501,II,III

Installation manual e-MatriXheat 800/500-6501,II,III

www.faberfires.com contact@faberfires.com