Electric fixed rack bakery oven - CF80
12Pages

Electric fixed rack bakery oven - CF80 SPEC SHEET : F9P-E000002-GB Pictures are not contractual. The company reserves the right to change any specifications without notice ‐ Copying forbidden.

INSTALLATION This machine is designed for professional use and thererefore must be installed in a work space which is NOT ACCESSIBLE TO THE PUBLIC for obvious safety reasons BEFORE THE INSTALLATION, MAKE SURE THAT : The equipment must be set up on a flat floor, with a sufficient safety allowable load. The oven will be installed on a FIREPROOF SUPPORT (IMPERATIVE) : wood, etc. ... BANNED for obvious safety reasons. The floor must withstand a minimum temperature of 300°C. The oven shouldn’t be in touch with any wall. Keep at least: Control board side : 10 mm to avoid condensation...

APPLIANCE CHARACTERISTICS The oven is made of : A stainless steel sheet assembly forming the tighten chamber A glass door with closure by electromagnet. An external stainless steel shell A stainless steel front face An automatic hood with 2 speeds controled by electronic (the frontage can be removed without any tool). An electronic control panel built in the door band RUNI FX DD V2 E-Drive : Touchscreen regulator (option) Control of the following functions (According to the oven equipement) : Steam Exhaust vent (damper) Hood Energy saving Control of the...

Stopgap control «MINICOM» (9P-12TSE00000) Control of the following functions : Steam, Exhaust vent (damper), Adjustment of set temperature. or Energy saving function - Half load (9P-12DMCH0000) PAKAGING Pre assembled (9P-12MDD00000) Disassembled (9P-12D0000000) 3 POSSIBLE PACKAGINGS Pre assembled Handling palett dimensions : Package dimensions : Pre assembled : Electric box located at the top of the oven but disconnected.. Disassembled : Electric box located at the top of the oven but disconnected + Front and rear parts linked up with 4 screws for transportation. DOOR HINGES...

Electric fixed rack bakery oven - CF80Left hinges Right hinges Side view Rear view278 Minimum height when oven is delivered dismantled Connection kit for rear steam exhaust (option). Inlets ©© and outlets ©@© are at customer’s charge and have to be in-service the day of installation. When the analysis results of water are critical, it is deeply recommended to treat the inlet water to avoid any scaling problem. The wall clearance at rear of the machine is at least 100mm [400 mm if steam exhaust duct is at rear of the oven and not at the top] to ensure that oven works well. The free space...

REAR VIEW / CONNECTIONS PRINCIPLE The oven must be aerated in an ambient atmosphere below 32°C (90°F), to ensure its proper operating. Do not obstruct the oven ventilation grids. Steam exhaust pipe 1 m mini - Ø 153mm NOT SUPPLIED WITH THE OVEN Water solenoid valve Slidding electric box Stainless steel elbow fitting F-F Ø153 Hood condensates draining Water supply Electric power supply Reducer FF Ø 3/4”-Ø 1/2” Elbow fitting Ø 3/4”MF U-bend Ø 1/2” Condensate draining to the sewer Fixing of the loading ramp to the floor

Seal with high temperature silicone and then cover with aluminium scotch Pipes fitting : Female / oven side, male / outlet. NOT SUPPLIED WITH THE OVEN Option : Reinforced flexible for draining of condensates 2 m. Water solenoid valve 1 x Stainless steel hose for water inlet 3 m or NOT SUPPLIED WITH THE OVEN

At customer’s charge and responsibility. To be installed by a professional chimney installer Manufacturer’s recommendation : connect vertically a stainless steel tube with a minimum length of 1 m of Ø 153mm NOT SUPPLIED WITH THE OVEN Stainless steel elbow fitting Ø 153mm - supplied with the oven It is forbidden : to connect the steam exhaust pipe to a chimney dedicated to the fumes. to reach the outside with an horizontal pipe. To optimize the draft of the steam exhaust chimney, you must install it as straight and vertical as possible.

OPTION : STEAM EXHAUST CONNECTION KIT FROM THE BACK Steam exhaust pipe 1 m mini - Ø 153mm NOT SUPPLIED WITH THE OVEN Stainless steel pipes The wall clearance at rear of the machine is at least 400 mm if steam exhaust duct is at rear of the oven and not at the top to ensure that oven works well. Reinforced flexible for draining of condensates Not supplied with the oven

At customer’s charge and responsibility. To be installed by a professional chimney installer Manufacturer’s recommendation : connect vertically a stainless steel tube with a minimum length of 1 m of Ø 153mm NOT SUPPLIED WITH THE OVEN Stainless steel tee - Option Stainless steel pipe - Option Stainless steel purging unit - Option Connect vertically a reinforced flexible hose for draining of condensates and suitable for temperatures around 100°C - Option It is forbidden : to connect the steam exhaust pipe to a chimney dedicated to the fumes. to reach the outside with an horizontal pipe....

® Front part of the trolley larger than rear part. Trays are inside the frame. © Rear part of the trolley less large than front part. Trays are in line with the frame © Way to insert the trolley in the oven

BEFORE UNDERTAKING ANY WORK ON THE EQUIPMENT Before undertaking any work on electrical parts, disconnect the supply to the appliance at the external disconnecting switch. Beware of residual voltage. To disconnect the appliance from the electric plug, never pull the wire. DO NOT TOUCH THE APPLIANCE With any wet or damp body parts. If you are barefoot. All work on the equipment must be done by a qualified and approved professional. In the event of false alarm in the safety system, you must contact your supplier. WATER QUALITY Although if clean and safe for consumption, the water supplied can...