Compact 2000 axial fans are quality units of proven Their compact, ultra low profile combined with a wide range of styles and sizes make them industries broad range of applications. Units suit duct, wall and roof unit mounting. All Compact 2000 units have been vigourously tested, achieving very accurate airflow, motor and noise level published data. The material finish ensures a very durable weather- Order Codes & Speed Dimensional Data

The Compact 2000 range provides 3 alternative styles in each of the 7 fan model sizes from 315 1o 630mm nominal diameter. Each model uses the established, Elta highly efficient aerofoil bladed impellers, produced from GRP Electrical input is via flying leads, or model selected. A wide selection of accessories is also available, including speed controllers. All units are protected • Plate Mounted • Ring Mounted Motor Design The Compact 2000 low profile is largely due to the compact design of its range of induction motors. Designed and matched to the aerodynamic performance of the impellers, these...

Electrical Inputs Most models, suit either 220/240V - 1ph - other supplies available, including 60Hz. Depending on model type, units are fitted with a 'protected* terminal box (IP55), or flying leads. Material & Finish The all metal fan casing and guards provide a long lasting robust construction. All parts are suitably treated to ensure full protection. Fan ducting and motorhousingsare powder coated in highly durable polyester epoxy , in a pastel beige (RAL 7032). Guards are bright zinc plated. Aerodynamic Impellers Elta's renowned, high efficiency adjustable pitch impellers with aerodynamic...

Three alternative styles of fan casing and mounting are available for each of the 7 model sizes. These should enable most application requirements to be met. Impeller guards are available - refer to • Plate mounted - CP series • Ring mounted - CR series Details of larger diameter Compact axial fans are available on request. ■ Plate Mounted - CR Series Extremely compact plate mounted style with venturi inlet and 4 hole mounting. • Supplied with flexible conduit/flying leads • Capacitor supplied loose (1 phase models) • Wire guard fitted on motor side of impeller

Ring Mounted - CR Series Ultra compact venturi ring style, based on the Plate style but with plate removed. Venturi mounting is via 4 holes which also retain the motor mounting guard. • Supplied with flexible conduit/flying leads • Capacitor supplied ioose (1 phase models) • Wire guard fitted on motor side of impeller Material & Finish Fan casings: Steel, coated in quality polyester epoxy powder paint, pastel — Guards: Steel, bright zinc plated. Motors: Die cast aluminuim fluted casing; finished in polyester epoxy powder coat paint beige (RAL 7032). Impellers: Natural colour (beige) GRP moulded...

Airflow Performance Curve For alternative selections please discuss with Elta Noise Level Data * Sound lovots are quoted as in-<Juct levels measured in accordance with BS 848 wrth the Ian operating at aptowmatery 50% ol rts peak pressure capacity. The acoustics arouod the <mtaOod Ian un-t will aHect Ihe dBA reading il measured when installed Speed Variation Airflow readings given are typical for units running at full nominal speed. All units are speed controllable down to 40% of nominal speed. Speed controller details are on Order Codes and Speed Controllers page.

Order Codes & Spee ' To comptote lui order code reference refer IO How to Order' below. To complete lull order code reference refer to 'How to Order' oolow. Each Compact 2000 basic 'fan model reference' is the same for each of the 3 The fan model reference defines the nominal fan diameter, speed and electrical input and therefore air performance. Having selected the fan model reference, simply add the style prefix code required (CP, CD or CR). For alternative electrical inputs etc. please discuss with Elta. or their NUMBER OF MOTOR POLES

Quality electronic type speed controllers, matched to the Compact 2000 range are available for panel/wall mounting. Each unit includes a speed control knob and separate on/off switch. Order codes are shown Elta recommend the use of 3 wire control on single phase fan units when speed controlled, with operation down to 100 volts being permissible. When speed control is required, Elta can only guarantee the fan unit, when operated via an Elta supplied controller and when the thermal overload protection is utilised. Single phase controllers pictured. In addition all wiring/cabling between the fan...

Dimensional Data ■ Plate Mounted - CR Series CAPACITOR PITTED M?0 HOLt 1U ISIN3LE PHASE MODELS ONLY) ACCEPT CONDUIT ■ Ring Mounted - CR Series

Impeller Guards A flat guard thai mounts directly over the impeller outlet on Ducted, Plate and Ring mounted models. Material & finish; Steel, hright 7inc Anti-Vibration Mounts Fits directly to the mounting feet of Ducted models to help minimise noise in sensitive locations. Supplied individually, complete with fixing. Material & finish; Rubber with steel insert. Nolo - Dimensions may vary with aitotnalivo suppliers

An attractive, all-weather louvre with vanes that open automatically when fan airflow commences. Fitsindependantlyof fan and ideally wall mounted downstream of fan unit. Supplied with fixings. • 7 sizes to suit each fan diameter • Wipe clean finish • Eliminates backdraft Material & finish; Durable polypropylene in light grey. Match)incj Flanges Fits directly to Ducted fan mounting flange to provide a coupling for a Flexible Collar, or an alternative fixing for any other matched interconnection e.g. customers ducting. Supplied individually less Material & finish; Steel, painted in pastel beige...

Elta Fans Ltd - Applied Technology Elta Fans Ltd - Building Services 17 Barnes Wallis Road, Segensworth East Industrial Estate, Pensnett Trading Estate, Kingswinford, Fareham, Hampshire, P015 5ST, United Kingdom. West Midlands, DY6 7US, United Kingdom. Visit: eltafans.com e-mail: [email protected] Applied Technology: Building Services: