*myarchiexpo

NANO SPA

1 / 2 PagesView full catalog

NANO SPA

Product catalog summary

Features

Available in 8 sizes ranging from 1-kW to 8-kW.
Easy installation with fully equipped and pre-wired units.
Robust and durable construction.
Ultra-reliable flow switch for safe operation.
Includes temperature thermostat and overheating sensor.
Compact and durable design.

Technical Drawings

Analogue control with a 1.2°C differential.
Constructed with titanium flow tube and heating element.
Can be mounted on the floor or vertically on a wall.
Features vortex, long-life, stay-clean heating element technology.
100% efficiency throughout the product's life.
Operates silently.

Specifications

Power Supply: 220-240V single phase, 380-415V three phase.
Flow Requirements: Minimum 1m³/h, Maximum 17m³/h.
Heating Element and Flow Tube: Grade 1 titanium.
Control Thermostat: Analogue 0 > 45°C with 1.2°C differential.
Safety Thermal Cut Out: 60°C with manual reset.
Flow Switch: Gold tipped reed switch with titanium fulcrum pin.
Relay: Surface mount DPDT Finder 66.82.8.230.0000.
Seals: High temperature special formula EPDM ferrules, TPE end fitting gaskets.
Water Connections: 1.5” BSP female thread with 1½” / 50mm stepped ABS unions for rigid pipe and 1½” / 1¼” stepped hose tails for flexible pipe.
International Protection Marking: IP44.
Frequency: 50/60 Hz.
Working Pressure: 4 bar maximum.
Mounting: Floor or wall mounting.

Models

Product codes vary based on power output and voltage requirements, e.g., N-SPA-T1-R for 1-kW, N-SPA-T8-R for 8-kW.
For voltages other than 400V, add -380 or -415 to the product code.

Contact Information

Address: Unit 11, Gunnels Wood Park, Stevenage, Hertfordshire SG1 2BH.
Email: [email protected]
Phone: +44 (0) 1438 749474
Website: www.elecro.co.uk

Catalog excerpts

Unit 11, Gunnels Wood Park, Stevenage, Hertfordshire SG1 2BH [email protected] | +44 (0) 1438 749474 www.elecro.co.uk Provides efﬁciency, safety and above all reliability to effortlessly heat your water to the desired temperature, the Nano SPA heater is an ideal solution for spas. FEATURES • Available in 8 sizes from 1-kW up to 8-kW • Analogue control with 1.2°C differential • Easy installation, fully equipped and pre-wired • Titanium ﬂow tube and titanium heating element • Robust, durable construction • Can be ﬂoor or vertically wall mounted • Ultra-reliable ﬂow switch allows safe operation • Vortex, long life, stay clean heating element technology • Supplied with temperature thermostat and overheating sensor • 100% e fﬁciency throughout the product lif e • Silent operation • Compact, durable design TECHNICAL DRAWINGS PRESSURE DROP PRESSURE (BAR)

Open the catalog to page 1

SPECIFICATIONS POWER SUPPLY 220-240V single phase, 380-415V three phase FLOW REQUIREMENTS HEATING ELEMENT FLOW TUBE CONTROL THERMOSTAT FLOW SWITCH Gold tipped reed switch with titanium fulcrum pin Surface mount DPDT Finder 66.82.8.230.0000 High temperature special formula EPDM ferrules, TPE end ﬁtting gask ets WATER CONNECTIONS 1.5” BSP female thread supplied with 1½” / 50mm st epped ABS unions for rigid pipe and 1½” / 1¼” st epped hose tails for ﬂexible pipe INTERNATIONAL PROTECTION MARKING WORKING PRESSURE Floor or wall mounting GROSS WEIGHT Power Output PRODUCT CODES * for voltages other than...

Open the catalog to page 2

NANO SPA

NANO SPA

Catalog excerpts

All Elecro Engineering LTD catalogs and technical brochures