*myarchiexpo

S260

Product catalog summary

Product Overview
The S260 electronic wall-mounted sensor soap dispenser is designed for installation on a dry wall or panel with permanent access for servicing. It is suitable for various sanitary facilities due to its multiple finishes and minimalist design.

Specifications

Finishes: Brushed stainless steel, Polished brass, Matte black
Dimensions: Ø28xL150mm
Viscosity: 100–3800 cPs
Soap Type: All types except microbead soap
Soap Dose: 1.4cc (adjustable)
Soap Tank Capacity: 1 Litre
Sensor Range: 35-155mm (adjustable)
Power Supply: 12V adaptor or 6 x Alcaline D batteries
Warranty: 5 years

Installation Instructions

Wall cut-out requires a 23 to 24mm hole for the spout and a 2 to 3mm hole for the anti-rotation pin.
Avoid installing sensors opposite reflective surfaces or other infrared devices.
Maintain a minimum distance of 300mm between the sensor and the washbasin bottom.

Maintenance Guidelines

Avoid using products containing hydrochloric acid, formic acid, acetic acid, or bleach with chlorine.
Do not use abrasive products or tools.
Clean with soap and water, then dry with a clean cloth.

Optional Accessories

Power splitters with 2, 3, or 4 outputs
Electrical cable extensions (1m and 3m)
Remote control for electronic soap dispensers
Junction box for connecting up to 10 soap dispensers

Catalog excerpts

TECHNICAL DATA SHEET Electronic soap dispenser Duten washroom accessories 328 chemin des Agonèdes I Zone artisanale I 30340 Saint-Julien-les-Rosiers Tél. 04 66 52 20 00 I Fax : 04 66 55 71 50 I [email protected] The S260 electronic wall-mounted sensor soap dispenser is designed for an installation on a dry wall or panel with permanent access to the mounting tail/nut for servicing and/or repairs. Suitable for all types of sanitary facilities thanks to its multiple choice of finishes and its minimalist look. Power supply Mains Mains Mains Battery Battery Battery Brushed stainless steel Polished brass finish Matte black finish Brushed stainless steel Polished brass finish Matte black finish Characteristics Finishes Brushed stainless steel (S)/Polished brass finish (B)/Matte black finish (N) All types, except microbead soap Soap dose 1.4cc (adjustable with remote control) Soap tank Sensor range 35-155mm (adjustable with remote control) Power supply Adaptor 12V (_SEC)-cable length 5M Battery case IP67 (_BAT)-cable length 0.50M batteries not included-6 x Alcaline D batteries Length of cable from rear of dispenser 1.30M (possibility to add cable extension(s)) Supply hose length 0.90M–distance between soap dispenser and tank

Open the catalog to page 1

Power splitter with 2 outputs Power splitter with 3 outputs Power splitter with 4 outputs Electrical cable male-female extension 1 meter Electrical cable male-female extension 3 meters Remote control for electronic soap dispensers Junction box 230/12V for connecting up to 10 soap dispensers Output cable for junction box female connector Installation info Wall cut-out The S260 is designed to be installed through a partition where there is a technical duct and/or permanent access to the mounting tail/nut for servicing and/or repairs. Drill a 23 to 24mm hole where you want to install the spout of...

Open the catalog to page 2

Duten washroom accessories 328 chemin des Agonèdes I Zone artisanale I 30340 Saint-Julien-les-Rosiers Tél. 04 66 52 20 00 I Fax : 04 66 55 71 50 I [email protected] Technical diagram-mains version

Open the catalog to page 3

Duten washroom accessories 328 chemin des Agonèdes I Zone artisanale I 30340 Saint-Julien-les-Rosiers Tél. 04 66 52 20 00 I Fax : 04 66 55 71 50 I [email protected] Technical diagram-battery version

Open the catalog to page 4

S260

S260

Catalog excerpts

All Duten catalogs and technical brochures