Catalog excerpts


Dulux? TRADE Dulux Trade Durable Flat Matt is a highly durable, water-based flat matt finish. It has excellent coverage and opacity. Suitable for all normal interior wall and ceiling surfaces, particularly those subject to high traffic such as corridors and stairwells. It also has an ultra low sheen level, perfect for masking areas of uneven wall surface. • Excellent Durability • Flat Matt Finish • High Opacity PRODUCT INFORMATION Typical Use Suitable for interior use on all normal interior wall and ceiling surfaces. For interior areas that are likely to suffer from mould growth, use Mouldshield Fungicidal Eggshell from Dulux Trade*. Pack Size 2.5L and 5L. Colour Range See appropriate Dulux Trade colour literature or visit duluxtrade.co.uk. Film Properties Chemical Resistance: Not suitable. Heat Resistance: Not suitable for use on heated surfaces, such as radiators. Water Resistance: Where surfaces are subject to a high degree of wear and tear and require a greater level of washability, Dulux Trade Diamond Eggshell is more suitable. Composition (nominal) Pigment: Lightfast Pigments. Binder: Acrylic Copolymer Emulsion. Solvent: Water. Volume Solids White - 36% (nominal). Other colours will vary. SURFACE PREPARATION To get the best results with Dulux Trade Durable Flat Matt, make sure surfaces to be painted are sound, clean, dry (new surfaces particularly must be fully dry). Remove all loose and defective paint. Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. Where necessary, wash the surface to remove dirt, grease and powdery or dusty residues. Rinse with clean water and allow to dry. Seal surfaces that remain powdery after thorough preparation with an appropriate plaster sealer. Where necessary, rub down and then wipe off with a damp, lint free cloth to avoid dust. Any surface defects should be filled with the appropriate Polycell Trade Polyfilla. SYSTEMS INFORMATION STIR THOROUGHLY BEFORE USE. Seal new or bare surfaces with a thinned first coat of Dulux Trade Durable Flat Matt (up to 1 part clean water to 5 parts paint). The normal finishing process is 2 full coats of Dulux Trade Durable Flat Matt but on previously painted surfaces in good condition where similar colours are used, 1 coat may be sufficient. For best colour consistency, purchase sufficient tinted paint for each job including touch-in at one time from the same source. APPLICATION METHOD Brush, roller, conventional spray or airless spray. As with other water-based paints, do not apply in temperatures below 8°C (as recommended by the British Standard BS 6150). Practical Coverage A guide to the practical coverage which can be achieved under normal conditions is up to 17m2 per litre.

Open the catalog to page 1

DURABLE FLAT MATT Dulux? TRADE Thinning Sealing new or bare surfaces: Add up to 1 part clean water to 5 parts paint. Normal use (not to be exceeded): Add up to 1 part clean water to 10 parts paint. Conventional spray application: Add up to 1 part clean water to 2.5 parts paint. Airless spray application: Add up to 1 part clean water to 5 parts paint. Spray Recommendations Conventional Spray: Satisfactory through most equipment. Airless Spray: A typical set up for airless spray would be a minimum working pressure on paint of 133 bars (2000lb/sq in) with a spray tip size 0.38mm (15 thou) and...

Open the catalog to page 2

All Dulux catalogs and technical brochures


    1 Pages


    3 Pages


    3 Pages


    3 Pages

  5. Diamond Range

    16 Pages

  6. T30314

    20 Pages

  7. T30064

    4 Pages

  8. T30028

    20 Pages

  9. T30345

    44 Pages

  10. T28107

    2 Pages

  11. T28114

    2 Pages

  12. T29241

    4 Pages

  13. T30089

    8 Pages

  14. Veri-Tag

    2 Pages

  15. T30308

    2 Pages

  16. T12134

    2 Pages

  17. colour guide

    15 Pages