SYSTEM INFORMATION Armstead Trade Durable Matt provides a tough and durable matt finish that is ideal for high trac areas. It is wipeable and oers good stain resistance. Suitable for all normal interior wall surfaces. Stir thoroughly before use. On very absorbent surfaces apply a sealing coat of thinned Armstead Trade Durable Matt. The normal finishing process is 2 full coats of Armstead Trade Durable Matt, but on previously painted surfaces in good condition, where similar colours are used, 1 coat may be sucient. As with other water-based paints, do not use when the temperature is below 10°C. Hardwearing, scrubbable matt finish Good stain resistance Ideal for high trac areas PACK SIZES WHITE WATER SPIRIT A guide to the practical coverage which can be achieved under normal conditions is up to 14m2 / litre. COLOUR RANGE Armstead Trade Exclusive: BS4800: RAL: NCS 1 & 2: 120 colours 42 colours 30 colours 1108 colours Visit www.armsteadtrade.co.uk/pp As with other water-based paints, do not apply in temperatures below 8ºC (as recommended by British Standard BS 6150) THINNING Sealing new/bare surfaces: Add up to 1 part clean water to 10 parts paint. Normal use (not to be exceeded): Thinning is not usually required. FILM PROPERTIES Chemical Resistance: Not recommended. Heat Resistance: Not suitable for use on heated surfaces. eg. radiators. Water Resistance: Resistant to the levels of atmospheric humidity present in normal interior environments and will withstand repeated washing. Suitable for use in kitchens and bathrooms. Not suitable for use on immersed surfaces or where there is heavy and prolonged condensation. Do not use externally. Conventional spray application: Add up to 1 part clean water to 5 parts paint. Airless spray application: Thinning is not usually required. SPRAY RECOMMENDATIONS Conventional Spray: Satisfactory through most equipment. Airless Spray: A typical recommendation for airless spray application is a minimum working pressure on paint of 140 kg/cm2 (2000 Ib/sq in) with a spray tip size 0.38mm (15 thou) and a spray tip angle 65°. COMPOSITION (NOMINAL) Pigment: Binder: Solvent: Brush, roller, spray and airless spray. Lightfast Pigments. Acrylic Copolymer Emulsion. Water. DRYING TIMES (SINGLE COAT, STANDARD THICKNESS) up to 12M 14M /L 15M2/L 8M2 16-24h 6-16h 2-4h 12h VOLUME SOLIDS WHITE WATER SPIRIT *Dependent upon temperature and humidity. 41% (nominal) for White, colours will vary. CLEANING UP SURFACE PREPARATION Surfaces must be sound, clean, dry and free from all defective or poorly adhering material, dirt, grease and salts. New plaster and masonry must be fully dry before priming. After use, remove as much paint as possible from brushes before cleaning with clean water. WHITE WATER SPIRIT TRANSPORTATION & STORAGE Note: Special precautions should be taken during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead. Do not use or store in extremes of temperature and protect from frost. To prevent spillage, please store and transport upright. Page 1 of 2

FURTHER SUPPORT EU limit value for this product (cat A/a) : 30g/l (2010). This product contains max. 14g/l VOC. Online: www.armsteadtrade.co.uk Email: [email protected] Phone: 08444-817-818 Please visit www.armsteadtrade.co.uk to download safety sheet SDSAM302 VOC Content Low 0.30% - 7.99%. VOCs (Volatile Organic Compounds) contribute to atmospheric pollution. Follow us on Twitter Let’s create together a better future for our planet. Find out how at: www.armsteadtrade.co.uk/pp AkzoNobel, the AkzoNobel logo, Armstead and Planet Possible are trademarks of the AkzoNobel group...