INFINITY® SYSTEM A Pressure-Equalized Rainscreen Exterior Insulation and Finish System Infinity Installation Details DS120

INFINITY®SYSTEM - GROOVE PATTERN DRYVIT SYSTEMS, INC. MAKES NO REPRESENTATION REGARDING CONFORMITY OF ITS SUGGESTIONS TO MODEL BUILDING CODES, ENGINEERING CRITERIA, SPECIFIC APPLICATIONS OR PROJECT LOCATIONS. ALL COMPONENTS INDICATED IN ILLUSTRATIONS, AS WELL AS OTHERS THAT MAY BE REQUIRED FOR THE INTEGRITY OF THE SYSTEM SHALL BE DESIGNED, DETAILED AND ENGINEERED BY REPRESENTATIVES OF THE ARCHITECT, OWNER OR CONTRACTOR TO BE IN CONFORMANCE WITH MODEL CODES, ARCHITECTURAL AND ENGINEERING REQUIREMENTS PERTAINING TO SPECIFIC BUILDING PROJECTS. DRYVIT SYSTEMS, INC. MAKES NO WARRANTY, EXPRESSED OR...

4 10/06 IS 0.0.01 NOTE: DRYVIT RECOMMENDS THAT GROUND FLOOR APPLICATIONS AND ALL FACADES EXPOSED TO ABNORMAL STRESS, HIGH TRAFFIC, OR DELIBERATE IMPACT HAVE THE BASE COAT REINFORCED WITH PANZER® MESH PRIOR TO I.S. REINFORCING MESH™. LOCATION OF HIGH IMPACT ZONES SHOULD BE INDICATED ON CONTRACT DRAWINGS. 1. APPROVED BY: RS REV: without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative...

Building Facade IS 0.0.02 3 10/06 APPROVED BY: RS REV: without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative any project. The project design professional determines, in its sole detail and for the architecture, design, engineering or workmanship of and Dryvit specifically disclaims any liability for the use of this standards. This detail is for general information and guidance...

DRYVIT VENT ASSEMBLY™ DRYVIT STARTER STRIP The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative is best suited...

610 MM (2'-0") DRYVIT STARTER STRIP VERTICAL GROOVES (ALIGNED) DRYVIT VENT ASSEMBLY™ The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally...

45 I.S. Insulation Board- Groove Pattern 3 10/06 IS 0.0.05 APPROVED BY: RS REV: without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative any project. The project design professional determines, in its sole detail and for the architecture, design, engineering or workmanship of and Dryvit specifically disclaims any liability for the use of this standards. This detail is for general...

DRYVIT AP ADHESIVE (SEE NOTE 2) DRYVIT VENT TRACK™ DRYVIT STARTER STRIP (SEE NOTE 1) I.S. INSULATION BOARD CLOSURE BLOCK (SEE NOTE 1) INFINITY®SYSTEM FILL DRYVIT VENT TRACK AT CLOSURE BLOCK LOCATION WITH AP ADHESIVE PRIOR TO SETTING CLOSURE BLOCK, TO PROVIDE COMPARTMENT CLOSURE. ADHERE CLOSURE BLOCKS AND STARTER STRIPS USING "RIBBON & DAB" ADHESIVE PATTERN TO PROVIDE COMPARTMENT CLOSURE. 2. NOTES: 1. APPROVED BY: RS REV: 3 DRYVIT BACKSTOP® NT APPROVED SUBSTRATE FRAMING I.S. INSULATION BOARD™ VERTICAL GROOVES (ALIGNED) DRYVIT VENT ASSEMBLY™ The architecture, engineering and design of the project...

without notice. Contact Dryvit to insure you have the most recent does not violate Dryvit's warranty. This detail is subject to change is best suited for the project. Use of a functionally equivalent detail discretion, whether this detail or a functionally equivalent alternative of any project. The project design professional determines, in its sole detail and for the architecture, design, engineering or workmanship and Dryvit specifically disclaims any liability for the use of this standards. This detail is for general information and guidance only professional. All systems must comply with...

professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only and Dryvit specifically disclaims any liability for the use of this detail and for the architecture, design, engineering or workmanship of any project. The project design professional determines, in its sole discretion, whether this detail or a functionally equivalent alternative is best suited for the project. Use of a functionally equivalent detail does not violate Dryvit's warranty. This detail is subject to change without notice. Contact Dryvit to insure...

12.7 MM (1/2") DATE: 4 10/06 REV: AS AN OPTION DRYVIT FLASHING TAPE SURFACE CONDITIONER™ AND DRYVIT FLASHING TAPE™ CAN BE USED. LIGHTLY SAND SURFACE OF TRACK TO MAXIMIZE ADHESION. SEALANT SHOULD NOT BE IN DIRECT CONTACT WITH ASPHALTIC ADHESIVE ON DRYVIT FLASHING TAPE. COVER DRYVIT FLASHING TAPE LAPS WITH POLYETHYLENE TAPE OR BACKER ROD. The architecture, engineering and design of the project using the Dryvit products is the responsibility of the project's design professional. All systems must comply with local building codes and standards. This detail is for general information and guidance only...