Domoreflect Pool PU2KTwo component, aliphatic polyurethane pool paintDOMOREFLECT POOL PU2K is a two component paint, based on aliphatic polyurethane, specific for exterior and interior pools, which offers protection and mechanical strength without being affected by direct sunlight. Field of application DOMOREFLECT POOL PU2K is suitable for application on: - Swimming pools - Water tanks - Artificial ponds - Any surface in permanent contact with water - Waterproof concrete surfaces and surfaces which are already waterproofed with DOMOLASTIC - All construction materials (mortar, concrete, brick, stone, tile, plasterboard, etc.) Advantages - No addition of solvent is required. - Non-yellowing and resistant to UV radiation. - Excellent coverage. - High bonding strength. - High abrasion resistance. - Easy cleaning with pressured water >6 atm. - Resistance to pool disinfection chemicals (chlorine and oxygen). - High resistance to water, cleaners, oils and lubricants. Method of use Substrate condition: New pool constructions should be waterproofed externally with coating DOMOSLURRY (2 layers) and internally with two components coating DOMOLASTIC (applied in 2-3 layers with spatula and use of reinforcement, see Technical Data Sheet). Old pool walls should also have waterproofing coatings externally and internally. If no internal waterproofing coating exists, should follow the steps below • Abrasion entirely of pre-existing pool paint. • Filling-repairing with DOMOREPAIR, depending on substrate's condition. • Cement smoothing with DOMORESIN after 24 hours. • Application of DOMOLASTIC in 2-3 layers with spatula and use of reinforcement after 10 days, in order the previous cement mortar to develop sufficient strength. If there is an internal waterproofing coating, then the preexisting pool paint (epoxy or not) should be scrubbed to remove at least the last layer. Prior to product application, primer the substrate with epoxy primer DOMOPOX FLOOR PRIMER or SERITAL PRIMER W if substrate is moist. Mixing: Mixing ratio: A (paste):B (liquid) 3:1 w/w The components A and B are packed in a default mixing ratio. Component B is added to component A. The two components are mixed with an electric agitator of low power (300 rpm). The mixing time should be at least 5 minutes until the mix is completely homogeneous. Application: The well-mixed DOMOREFLECT POOL PU2K is applied on the well-prepared support by roller, brush or airless spraying machine (beck 21-25). DOMOREFLECT POOL PU2K is applied in two layers. The second layer should be applied crosswise once the first layer is completely dry.

- The product is sensitive to humidity and should not be applied in moist conditions (>60%). Therefore, avoid application during the morning hours (especially in winter). - Surfaces once painted with DOMOREFLECT POOL PU2K, should be protected from rain, as the contact with the water before the curing of the paint will affect the adhesion. - For economy and convenience apply primer and one layer blue DOMOREFLECT POOL PU2K on blue DOMOLASTIC. - Pools painted with DOMOREFLECT POOL PU2K are ready for use 14 days after the last application layer. Warning, traffic and working is not allowed on painted...

Time 90 minutes 60 minutes 45 minutes Time between layers (DOMOREFLECT POOL PU2K on DOMOPOX FLOOR PRIMER/SERITAL PRIMER W) Minimum 24 hours 16 hours 10 hours Maximum 48 hours 48 hours 36 hours Time between layers (DOMOREFLECT POOL PU2K on DOMOREFLECT POOL PU2K) Minimum 24 hours 16 hours 10 hours Maximum 48 hours 48 hours 36 hours Applied product ready to be used Walkability 48 hours 24 hours 18 hours Light Load 7 days 5 days 3 days Full Hardening 14 days 10 days 7 days All the technical data stated in the present Technical Data Sheet are based on laboratory tests and the knowledge and experience...