Air-to-water heat pump for indoor installation. Installation location: Max. flow temperature: 60 °C Casing colour: White (similar to RAL 9003) Heat pump for heating purposes for indoor installation with integrated heat pump manager WPM Econ5 with standard display. The integrated control panel can also be used as a wired remote control using the wall mounting set (special accessories for MS PGD). The integrated air circuit enables corner or wall installation with air ducts at the air intake and the air outlet side. Sound-optimised through lownoise axial fan and vibration-isolated compressor. High coefficients of performance (COP) using an evaporator optimised for heating operation and energy-efficient defrosting by reverse circulation. Universal design with two compressors for output regulation when operating at partial load, optional domestic hot water preparation and flexible expansion options for: Bivalent or bivalent-renewable operating mode Distribution systems with unmixed and mixed heating circuits At an external temperature of -10 °C, the maximum flow temperature that can be achieved is 53 °C. Dirt trap and flow rate switch built in. Flow and return sensor integrated; external sensor (standard NTC-2) in the scope of supply. Heat pump white textured (similar to RAL 9003). Glen Dimplex Thermal Solutions (Glen Dimplex Deutschland GmbH) Am Goldenen Feld 18 D-95326 Kulmbach Glen Dimplex Austria GmbH Hauptstraße 71 A-5302 Henndorf am Wallersee Technical changes, delivery options and errors excepted

LI 24TES Technical data Dimplex Air-to-water heat pump for indoor installation. (Low temperature) Heat pump code Lower operating limit heat source (heating operation) / Upper operating limit heat source (heating operation) Nominal power consumption according to EN 14511 at A2/W35 Nominal power consumption A7/W35 Sound power level Refrigerant / Amount of refrigerant Max. heating water flow rate / Pressure drop Heat source flow (min.) Width x Height x Depth ** Rated voltage Starting current Reverse circulation Heat pump seal of approval (valid until) *Heat output and coefficient of performance...

Article number Sample item Elasticated sound insulation underlay strips DN 32 double-sphere rubber expansion joint Heating water hose connection set El. cont. circulating pump: Control type Δp-c, fixed speed; PWM control optional Hydraulic tower 300 litres Transport aid for Hydro-Tower / LAW indoor unit Free-standing buffer tank 200 l Universal buffer tank (500 l) Dual differential pressureless manifold High-efficiency circulating pump DN 32 with coupling relay High-efficiency wet-running pump PWM with coupling relay Mixed heating circuit module Domestic hot water module/unmixed heating circuit...

Data sheet LI 24TES LI 24TES Description Article number Sample item Electronically controlled wet-running pump, selfregulating Electronically controlled wet-running pump, selfregulating Ready-for-use DN 32 stainless steel Wellflex pipe Ready-for-use DN 32 stainless steel Wellflex pipe Ready-for-use DN 32 stainless steel Wellflex pipe Ready-for-use DN 32 stainless steel Wellflex pipe Ready-for-use DN 32 stainless steel Wellflex pipe Immersion heater pipe assembly Fan convector heating with EC fan Fan convector heating with EC fan Fan convector heating with EC fan Fan convector heating with EC...

Data sheet LI 24TES LI 24TES Description Article number Sample item Safety valve combination Pump unit DN 32 for direct connection of the domestic WPG 32 hot water cylinder Extension for an Ethernet network connection Expansion module WPM for a KNX/EIB connection Extension for a Modbus RTU connection Swimming pool/remote fault indicator relay module Outside temperature sensor with casing Temperature sensor NTC-10 with metal sleeve Domestic hot water cylinder (500l) with temperature sensor Control accessories * Other specific accessories available / required Important information: The combination...

LI 24TES Note: The given hydraulic integration schematic is a schematic representation of the key components and serves as an aid for planning your customized system. The current status is available at all times under www.dimplex.de/nc /en/professional/online-planner/hydraulicintegrations.html. It does not contain all the required safety devices, the components needed to maintain constant pressure, or any other additional valves which may be required for maintenance and service work as stipulated by EN 12828. The heat pump manager settings and any external regulation system which may be connected...

• Air-to-water heat pumps with defrosting by reverse circulation extract the energy required for defrosting from the heating system. In the case of air-to-water heat pumps, a buffer tank connected in series, into which the immersion heater is screwed, must be installed in the flow in mono energy systems to ensure defrosting. A dirt trap with a mesh size of between 0.6mm and 0.8mm is to be installed in order to protect the plate heat exchanger from larger dirt deposits. Clean the filter sieve of the dirt trap one day after start-up. These intervals can be extended as soon as no more impurities...

Glen Dimplex Thermal Solutions (Glen Dimplex Deutschland GmbH) Am Goldenen Feld 18 D-95326 Kulmbach Glen Dimplex Austria GmbH Hauptstraße 71 A-5302 Henndorf am Wallersee Technical changes, delivery options and errors excepted.

Heat Pump Air-to-water heat pump Brine-to-water heat pump Water-to-water heat pump Reversible air-to-water heat pump Reversible brine-to-water heat pump Reversible water-to-water heat pump Air-to-water heat pump split design Heating circuit only Heat source Hydraulic tower Scalding protection Hydro tower HWK 332 Heat pump manager Parallel buffer tank Buffer tank Hot water cylinder Swimming pool heat exchanger Passive cooling station with cooling controller N6 Heating and silent or dynamic cooling Fan convector with 4-wire connection Cooling circuit only Domestic hot water distribution system:...