Group: Saint-Gobain
Catalog excerpts
Description Decoustics compound curved panels provide architects and designers with domed ceilings that have an acoustical solution to the problems of sound focussing and reflection normally associated with traditional hard surface finishes such as gypsum board, plaster, glass reinforced gypsum (GRG), fiber reinforced polyester (FRP), or wood. Dome shaped panels consist of compound, three-dimensional factory precurved units using one radius in all directions throughout the curve. Domed ceilings are made up of multiple, precisely engineered panel sections. Any one of several mounting methods can be employed depending on plenum access requirements, available substrate, plenum clearance, and panel joint preference e.g. closed reveal or open reveal only. Panels All Decoustics panels are custom fabricated and offered in a variety of types, sizes, thicknesses and finishes. Limitations Minimum radius is 10'-0" (3050 mm). Panel sizes are limited depending on radius of dome. Design Considerations The panels alone can form the dome without the need for a domed substrate. If, however, a domed substrate already exists, panels can be directly mounted to it. Dome shaped panels are only available with a fabric finish. Decoustics recommends 2" (50 mm) thick panels to be used in all dome areas. Providing the minimum radius requirement is met, it is possible to manufacture Dome Shaped panels consisting of more than one radius, e.g. elliptical. Depending on panel radius and thickness, exposed darting along edges may result with some fabric finishes which may or may not be prominent. However, darting is minimized when using Decoustics standard fabrics. Contact Decoustics for specific information. …cont’d Ceilings Custom Curved DOMES Substrate Panel Reveal cover strip Suspension Dome clip Fabric covered closure strip Precurve: “C” Channel Panel REVEAL EDGE OPTIONS
Open the catalog to page 1e-mail: sales@www.decoustics.com decoustics.com For LEED, BREEAM, and environmental information, please visit our website’s home page. 06/10 Ceilencio, Claro, Metallo, Quadrillo, Solo and Trelisio are trademarks of Decoustics Limited. Although rare and depending on panel radius, finish, and lighting conditions, some manufacturing "ridge" lines may be visible which are caused primarily by inherent density variations in the core material and may be unavoidable. Consult Decoustics for best finishes to use with specific lighting. Maintenance Refer to appropriate Decoustics “Cleaning and...
Open the catalog to page 2All Decoustics catalogs and technical brochures
-
Nuvola
8 Pages
-
Madero
20 Pages
-
Design Returns
4 Pages
-
Linear Wood & Linear Grille
4 Pages
-
LightFrame
8 Pages
-
Ceilencio What's New
2 Pages
-
Corporate
12 Pages
-
Air Renew
4 Pages
-
Metallo
2 Pages
-
High_Impact_Extreme
2 Pages
-
Low Frequency Tuner (LFT)
2 Pages
-
Suspended Reveal
2 Pages
-
Architectural Forms HCC
2 Pages
-
Architectural Forms HHC-Thin
2 Pages
-
Solo-T
2 Pages
-
Ceilencio
2 Pages
-
Claro-T
4 Pages
-
Solo-M
2 Pages
-
Coffer panel
2 Pages
-
Custom Curved Vault
2 Pages
-
Custom Curved Cones
2 Pages
-
Span
2 Pages
Archived catalogs
-
Suspended Accesible Reveal
2 Pages
-
Direct Mount system
2 Pages
-
Metallo
2 Pages
-
Claro
2 Pages
-
Stria Panel
2 Pages
-
Reflective Panel
2 Pages
-
Applique Panel (AQE)
2 Pages
-
Acoustical Panel (AP)
2 Pages
-
Trelisio Woven Wire Panel
2 Pages
-
Quadrillo Panel
2 Pages
-
Lay-In Panel
2 Pages
-
Direct Suspended System
2 Pages
-
Decoustics Recycled Content
9 Pages
-
Wall Panel Mounting Details
2 Pages
-
Wall Panel ArrangementsWall
2 Pages
-
Solo Installation
2 Pages