Modulens
44Pages

Gas fired floor-standing condensing boiler User Guide

4.3.4 Setting the contrast and lighting on the

1.1.1. Symbols used in the manual In these instructions, various danger levels are employed to draw the user's attention to particular information. In so doing, we wish to safeguard the user's safety, obviate hazards and guarantee correct Risk of a dangerous situation causing serious physical Risk of a dangerous situation causing slight physical Risk of material damage. Signals important information. Signals a referral to other instructions or other pages in the 1.1.2. Symbols used on the equipment Alternating current Caution dangerous live part Disconnect the appliance from the mains...

► 3CE: Collective conduit for sealed boiler ► Interscenario switch: Home automation switch that can be used to centralise and control several scenarios ► Hi: Lower heating value LHV (Nett) ► Hs: Higher heating value HHV (Gross) ► PPS: Polypropylene hardly inflammable ► PCU: Primary Control Unit - PCB for managing burner operation ► PSU: Parameter Storage Unit - Parameter storage for PCBs ► SCU: Secondary Control Unit - control panel PCB ► HL: High Load - DHW tank with plate exchanger ► SL: Standard Load - DHW tank with coil ► SHL: Solar High Load - Solar DHW tank with plate exchanger ► SSL:...

► Carry out installation in compliance with the prevailing legislation ► Perform the initial start up and carry out any checks necessary. ► Explain the installation to the user. ► If a maintenance is necessary, warn the user of the obligation to check the appliance and maintain it in good working order. ► Give all the instruction manuals to the user. To guarantee optimum operation of the appliance, the user must respect the following instructions: ► Read and follow the instructions given in the manuals provided ► Call on qualified professionals to carry out installation and initial ► Get...

2. Safety instructions and recommendations 1. Do not use a naked flame, do not smoke, do not operate electrical contacts or switches (doorbell, light, motor, lift, etc.). 5. Call your fitter. If you smell flue gases: 4. Call your fitter. Depending on the settings of the appliance: ► The temperature of the flue gas conduits may exceed ► The temperature of the radiators may reach 85°C. ► The temperature of the domestic hot water may reach Do not neglect to service the appliance: ► For completely safe and optimum operation, you must have your boiler regularly serviced by an approved installer.

2. Safety instructions and recommendations Only qualified professionals are authorised to work on the ► Regularly check the water pressure in the installation (minimum pressure 0,8 bar, recommended pressure between 1,5 and 2,0 ► Keep the appliance accessible at all times. ► Never remove or cover labels and rating plates affixed to the appliance. Labels and rating plates must be legible throughout the entire lifetime of the appliance. ► The appliance should be on Summer or Antrifreeze mode rather than switched off to guarantee the following functions: - Anti blocking of pumps - Frost...

Air is sucked in by the fan and gas injected into the venturi by the fan intake. The fan rotation speed is set according to the settings parameters, the thermal energy requirement and the temperatures measured by the temperature sensors. The gas and air are mixed in the venturi. The gas/air ratio ensures that the quantities of gas and air are adjusted to each other. This provides optimum combustion on the entire output range. The gas/air mixture is fed into the burner on The burner heats the heating water circulating in the heat exchanger. At a return temperature lower than around 55°C, the...

Flue gas discharge pipe Flue gas measuring point Heat exchanger Ignition/ionization electrode Control panel Command module Water pressure sensor Shunt pump Safety valve Expansion vessel Combined venturi and gas valve unit Mixer pipe

A Temperature setting key (heating, DHW, swimming pool) B Operating mode selection key D Key to access the parameters reserved for the installer E Keys on which the function varies as and when selections F Rotary setting button: ► Turn the rotary button to scroll through the menus or ► Press the rotary button to access the menu selected or confirm a value modification

AGC 10/15 - AGC 15 - AGC 25 - AGC 35 3. Description 3.3.2. Description of the display n Key functions > 16 18 20 22 9 C002696-A I < J Selection of comfort mode or selection of the days to be programmed Selection of reduced mode or deselection of the days to be programmed Back to the previous level Back to the previous level without saving the modifications made Manual reset 24 bar # F AUTO % $ ! Reset of the time programmes t 14 STD ESC 12 Used to display the curve of the parameter selected j 10 f v 8 The symbol is displayed when help is available b 6 Used to scroll through the parameters ?...

The solar load pump is running The top part of the tank is reheated to the tank set point The entire tank is reheated to the tank set point The entire tank is reheated to the solar tank set point The tank is not loaded - Presence of the solar control Operating modes Summer mode: The heating is off. Domestic hot water WINTER mode: Heating and domestic hot water working Operation in automatic mode according to the timer Comfort mode: The symbol is displayed when a DAY override (comfort) is activated ► Flashing symbol: Temporary override ► Steady symbol: Permanent override Reduced mode: The...

System pressure bar Pressure indicator: The symbol is displayed when a water pressure sensor is connected. ► Flashing symbol: The water pressure is insufficient. ► Steady symbol: The water pressure is sufficient. ..ill Water pressure level Domestic Hot Water override A bar is displayed when a DHW override is activated: ► Flashing bar: Temporary override ► Steady bar: Permanent override Other information The symbol is displayed when domestic hot water Valve indicator: The symbol is displayed when a 3-way The symbol is displayed when the pump is operating. Name of the circuit for which the...