SCAFFOLD ACCESSORIES
1 / 8Pages

Catalog excerpts

SCAFFOLD ACCESSORIES - 2

M INITIAL COMPONENTS ■ FIXED BASE The 1000 jack base with 2 levers is primarily used to stabilize structures, in combination with stabilizers. ■ SWIVEL JACK BASE For flat surfaces. With holes in the spigot for attaching the cradle head. The reinforced base plate has a thickness of 5 mm and a surface area of 120 X 120 mm. Cold galvanized surface coating. They bear the load of the vertical pipes (Meka 48) or the scaffold frames. The reinforced base plate has a thickness of 5 mm and a surface area of 120 X 120 mm. 036 mm threaded rod available in different lengths. With overlapping space in...

Open the catalog to page 2
SCAFFOLD ACCESSORIES - 3

M WHEELS WITH SCREW JACK & Made of steel with cold galvanized surface coating. Plastic 020 cm wheel, 5 cm in width Adjustable screw jack 60 cm high and 036 mm. With fastening device that blocks the movement of the wheel when the brake is applied. ■ WHEEL WITH SCREW JACK HR (750) COMPONENT WEIGHT (kg) MAX. REG. (cm) REFERENCE WHEEL WITH SCREW JACK HE 250 5.8 40 025000200 Made of steel with cold galvanized surface coating. Nylon 020 cm wheel, 5 cm in width (synthetic fiber) Adjustable screw jack 50 cm high and 038 mm. With fastening device that blocks the movement of the wheel when the brake...

Open the catalog to page 3
SCAFFOLD ACCESSORIES - 4

Screw ties. 22 mm spanner. Cold galvanized surface coating. THE 048 CLAMPS COMPLY WITH THE REGULATION EN 74-1 ■ CLAMPS WITH WEDGE PIN (SWIVEL) Scaffold tie with wedge pin. Galvanized coating. Screw ties. 19 mm spanner. Surface coating with epoxy paint (suitable for exterior use). An indispensable component for securing the scaffolding to the structure's fagade. They should be used with an EN 74 round tube clamp for 048 mm pipe. Made of 048.3 mm steel pipe, fitted with an 018 mm hook, both in St-44 steel (S275 JR) Threaded rings to be fitted to the plugs, made of galvanized steel. The tie is...

Open the catalog to page 4
SCAFFOLD ACCESSORIES - 5

Hot-dip galvanized steel pipes with a minimum thickness of 75 microns. They are used as an auxiliary component that can be adapted using clamps to the different scaffold systems. Available in 048x3 mm section in compliance with regulation EN-39. Specific weight 3.5 kg/ml. Available in various lengths. PIPE 500 (GA) PIPE 1000 (GA) PIPE 1500 (GA) PIPE 2000 (GA) PIPE 2500 (GA) PIPE 3000 (GA) PIPE 4000 (GA) PIPE 5000 (GA) PIPE 6000 (GA) J 4) Pulley made of 040 mm steel pipe and support bar with a 25 L-shaped profile. The structure is fitted using two 042-48 mm clamps. The 0250 mm pulley roller...

Open the catalog to page 5
SCAFFOLD ACCESSORIES - 6

They enable the gap between scaffold modules to be covered and make the passageway continuous. Made with non-slip checker plate Structures are available designed for L-shaped profiles to improve their performance when flexed and with two slots on each corner to attach them where they provide support. Hot-dip galvanized and with a minimum thickness of 75 microns. B REINFORCED BEAMS WITH OPEN ENDS Px/w/w/wa Made of 048 MM pipes connected handrails with a rectangular crosssection. For applications on hanging scaffolds, forming trusses, strapping fagades on stabilizers, etc. Excellent ratio of...

Open the catalog to page 6
SCAFFOLD ACCESSORIES - 7

SCAFFOLD ACCESSORIES BLSCAFFOLD PLATE Made from polypropylene that is resistant to ultraviolet (UV) rays. They enable the loads transmitted by the scaffold through the jack bases to be spread across the ground. They enhance visibility and protect the ground. Successfully tested with 10 tonne loads. Easily stacked. Corners allow water drainage. JACK HOLDER These enable the wheels or jack bases of towers to be held so that lifting operations (e.g. cranes) can be performed in complete safety. They are fitted to the vertical pipe of the scaffold frame with a clamp and have two round commercial...

Open the catalog to page 7
SCAFFOLD ACCESSORIES - 8

DACAME, S.L. Ctra. Santa Barbara - La Sénia, km 4,6 43515 - La Galera TOVRheiniand CERTIFIED ATIFIED | ‘wrerei.tav.com bepopersi Multidirectional scaffold Mobile aluminium towers European scaffold DINO 48 Facade scaffold Mobile steel towers SYS-FAST Ce) Mobile steel towers European scaffold FREE 48 Facade scaffold DCM 49 Supporting Tower FORK HEAD D Conventional Scaffold Stages, ramps and grandstands Access Towers Product manufacturer: The content of this catalogue in protected in its entirety by copyright. It is completely prohibited to copy the images, texts, illustrations and graphic...

Open the catalog to page 8

All DACAME catalogs and technical brochures

  1. SYS-FAST

    8 Pages

  2. ALU 50

    8 Pages

  3. Duo 45

    6 Pages

  4. Dino 48

    16 Pages

  5. MEKA 48

    20 Pages

  6. Product list

    52 Pages

  7. LIFTING

    24 Pages

  8. EQUIPMENT

    20 Pages

  9. PROPS

    4 Pages