Catalogs >
CRESTRON >
mp-amp30_1

mp-amp30_1
3Pages

Catalog excerpts

MP-AMP30 Media Presentation Audio Amplifier >> Compact stereo power amplifier >> 15 Watts per channel into 8 or 4 Ohms >> Stereo or mono-summed operation >> High-efficiency Class D topology >> Energy saving design reduces power consumption when idle >> Convection cooled for noiseless operation >> Simple volume, bass, and treble adjustments >> Built-in loudness contour circuit >> Electronic short-circuit and overload protection >> Detachable terminal block speaker connections >> Unbalanced RCA line input, 3’ cable included >> Integral surface mounting flanges >> UL 2043 compliant for installation within a plenum-rated suspended ceiling[1] The Crestron® MP-AMP30 provides a convenient, low-cost audio amplifier solution for a variety of applications. A perfect complement to the entire Media Presentation line from Crestron, it features a compact surfacemountable design that installs virtually anywhere without requiring an equipment rack. The MP-AMP30 meets the requirements of UL 2043 for installation in an environmental air-handling (plenum) space, such as above a suspended ceiling[1]. High-efficiency Class D circuitry delivers 15 Watts per channel to drive one or two pairs of 8 Ohm speakers, or a single pair of 4 Ohm speakers, making it ideal to support stereo speakers at the front of a room or mono speakers in the ceiling. Mono-summed operation is enabled by changing two jumpers on the front panel. Refined, reliable operation is ensured thanks to pop-free turn-on circuitry and electronic short-circuit and overload protection. An energy-saving design achieves optimum efficiency under load, and the amplifier powers down automatically when no input signal is detected for more than 5 minutes, reducing overall power consumption and heat as part of a green system design. The amplifier quickly powers back on the instant an input signal is detected. Its extruded aluminum housing is both attractive and effective at dissipating heat, affording a silent running design without cooling fans. Installation and setup of the MP-AMP30 is simple. Detachable output connectors facilitate the termination of speaker wiring up to 16 gauge. RCA inputs connect directly to the line output of a video projector or display, audio processor, mixer, or AV switcher. Rotary controls provide for adjusting the overall speaker volume, as well as bass and treble. For quiet environments, loudness compensation is employed by setting the volume control below the center detent position. SPECIFICATIONS Audio Input Volume Range: -55dB to +20dB Loudness: Active at volume settings below center detent Bass Gain Range: ±15dB @ 100Hz Treble Gain Range: ±15dB @ 10kHz Frequency Response: 20Hz to 20kHz ±0.5dB S/N Ratio: 75dB 20Hz to 20kHz A-weighted THD+N: 0.7% 20Hz to 20kHz Output Power: 15 Watts per channel at 8 or 4 Ohms Amplifier Protection: Electronic short-circuit and overload protection Connectors – Top Panel AUDIO OUT 8Ω: (2) 2-pin 3.5mm detachable terminal blocks; Left & right channel speaker-level audio outputs; Wire Size: Connector accepts 16 AWG maximum; Output Power: 15 Watts per channel at 8 or 4 Ohms Connectors – Bottom Panel AUDIO IN: (2) RCA female, unbalanced stereo line-level audio input; Maximum Input Level: 2 Vrms; Input Impedance: 18k Ohms; 3 ft (0.9 m) stereo RCA-RCA cable included PWR 24VDC 2.0A: (1) 2.1 x 5.5 mm DC power connector; 24 Volt DC

Open the catalog to page 1

MP-AMP30 Media Presentation Audio Amplifier MP-AMP30 – Front, Top and Bottom Views Controls & Indicators BASS: Rotary low frequency boost/cut adjustment, flat at center detent TREBLE: Rotary high frequency boost/cut adjustment, flat at center detent VOL: Rotary input level adjustment ST, MO: Mode selection jumpers, select stereo or mono-summed operation Power: (1) green LED, indicates operating power supplied from external power pack Height: 5.85 in (149 mm) Width: 3.91 in (100 mm) Depth: 1.43 in (37 mm) Power Requirements MODELS & ACCESSORIES Power Pack: 2.0 Amps @ 24 Volts DC;...

Open the catalog to page 2

MP-AMP30 Media Presentation Audio Amplifier Notes: 1. The MP-AMP30 is tested by an NRTL (Nationally Recognized Testing Laboratory) and complies to ANSI/UL2043 (Fire Test For Products Installed in Air-Handling Spaces). Full compliance requires plenum rated cables such as Crestron CBL-KAUDIO-RCAM2-L-P-50 audio cable, CBL-SPK-P-35 speaker cable, and CBL-PWR-EXT24V-P-6 DC power extension cable. Please note that the included power pack is not ANSI/UL2043 compliant, and thus cannot be installed in an air-handling space unless enclosed in a suitable plenum-rated enclosure. Crestron Electronics,...

Open the catalog to page 3