1. Catalogs
  2. CRESTRON
  3. CLX-2DIMFLV8-277

CLX-2DIMFLV8-277
1 /3Pages

CLX-2DIMFLV8-277

CLX-2DIMFLV8-277
1 /3Pages

Catalog excerpts

CLX-2DIMFLV8-277-1

CLX-2DIMFLV8-277 8 Channel 0-10V Dimmer Module, 2 Feeds, 277V > Eight-channel 0-10V dimmer module for commercial lighting applications > Installs in a Crestron® CAEN enclosure > Supports 0-10V dimmable fluorescent ballasts and LED drivers > Also supports on/off switching of non-dimmable lighting loads > Single or dual feeds — two four-channel dimmers in one module > Rated 16 Amps per channel, 32 Amps total (using two 20 Amp feeds), at 277 Volts AC > Customizable dimming curves via software > Arcless switching > Built-in air gap relay per channel > Closure-activated override mode > UL® 924 and CSA® C22.2 No. 141-15 listed for emergency lighting control > Crestron system integration via Cresnet® > Easy termination using a CLT-2DIMFLV8-277 terminal block (sold separately) > CEC Title 24 2013 compliant The Crestron® CLX-2DIMFLV8-277 is an eight-channel, two-feed dimmer module designed for 277V lighting system applications. It installs in a CAEN enclosure and provides control of 0-10 Volt dimmable fluorescent ballasts and LED drivers. It can also be used to switch non-dimmable lighting loads. Dual feed capability provides two independent four-channel dimmers in one module space. Each output channel is rated for 16 Amps, with a total module rating of 32 Amps when fed from two separate 20 Amp feeds. Centralized Lighting Cabinet Installation Crestron CLX series lighting control modules are designed to be installed in a CAEN wall mount enclosure. Available in a variety of sizes, CAEN enclosures provide a scalable, high-density centralized lighting control solution for any-sized residence. A selection of CLX module types is offered to accommodate a wide range of load types and system configurations. Termination of high-voltage wiring to the CLX-2DIMFLV8-277 module is facilitated using a CLT-2DIMFLV8-277 terminal block, which is sold separately to enable termination of the wiring prior to installing the module. This terminal block mounts beside the module within the enclosure. The 0-10V control wires terminate to the front of the module via detachable terminal blocks. Other low-voltage control signals are bussed between each of the modules within an enclosure via a simple 5-wire link (interconnect jumpers included), which terminates to a single terminal block (model CAEN-BLOCK, sold separately) at the bottom of the enclosure. Shown with CLT-2DIMFLV8-277 terminal block (sold separately) Cresnet® Communications The CLX-2DIMFLV8-277 interfaces with a Crestron control system (a.k.a., control processor or automation processor) via Cresnet. Cresnet is a simple 4-wire network bus that provides the communications backbone for a system of Crestron lighting dimmers, switches, keypads, shades, thermostats, and other devices. Emergency Lighting Control The CLX-2DIMFLV8-277 is UL® 924 and CSA® C22.2 No. 141-15 listed for use in controlling emergency lighting loads. In the event of a power failure, a contact closure from a power loss sensor (Crestron GLS-PLS-120/277, sold separately) activates the override mode in the CLX-2DIMFLV8-277 to turn on each designated lighting load if it is off (assuming line power is supplied by a backup power source). The override dimming level can be preset to any value when commissioning the lighting system, so even if the load is already on prior to a power failure, it will change to the preset level when override mode is act

 Open the catalog to page 1
CLX-2DIMFLV8-277-2

CLX-2DIMFLV8-277  8 Channel 0-10V Dimmer Module, 2 Feeds, 277V SPECIFICATIONS Heat Dissipation: 45 BTU/hr Load Control Dimmer Channels: 8 Dimmable Load Types: 0-10 Volt fluorescent ballasts or LED drivers (4-wire) Switched Load Types: LED, incandescent, fluorescent, magnetic lowvoltage, electronic low-voltage, high-intensity discharge (HID) Per Channel Load Rating: 16 Amps Per Group Load Rating: Group 1 (Channels 1-4): 16 Amps; Group 2 (Channels 5-8): 16 Amps Module Total Load Rating: 32 Amps [1] Line/Load Voltage: 277 Volts AC, 50/60 Hz; requires one or two singlephase feeds (may be same or...

 Open the catalog to page 2
CLX-2DIMFLV8-277-3

Crestron Electronics, Inc.  15 Volvo Drive    Rockleigh, NJ 07647 Tel: 800.237.2041 / 201.767.3400 www.crestron.com All brand names, product names and trademarks are the property of their respective owners. ©2021 Crestron Electronics, Inc. Specifications subject to change without notice. Revised 06

 Open the catalog to page 3

All CRESTRON catalogs and technical brochures

  1. TSW-1070

    9  Pages

  2. C2N-VEQ4

    4  Pages

  3. RMK-AMP-X

    7  Pages

  4. AMP-X50MP

    4  Pages

  5. AMP-PNMK

    2  Pages

  6. AM-3200

    6  Pages

  7. HD-PS402

    7  Pages

  8. HD-PS401

    7  Pages

  9. HD-PS622

    7  Pages

  10. HD-PS621

    7  Pages

  11. TSW‑570

    7  Pages

  12. TSW‑570P

    8  Pages

  13. TSW-770

    9  Pages

  14. DM-NVX-E760C

    5  Pages

  15. TSW-1070R

    6  Pages

  16. HR-310

    3  Pages

  17. TSR-310

    5  Pages

  18. MC4-R

    5  Pages

  19. UC-B160-T

    6  Pages

  20. DGE-100

    6  Pages

  21. UC-SB1-HUDDLE

    5  Pages

  22. CEN-CI3-1

    3  Pages

  23. mp-amp30_1

    3  Pages

  24. MP-AMP30

    16  Pages

  25. cen-ups1250_1

    40  Pages

  26. Best_Light

    4  Pages

  27. AMP-3210T

    4  Pages

  28. AMP-8150

    4  Pages

  29. DMPS3-4K

    1  Page

  30. DMPS3-4K

    2  Pages

  31. HD-MD-400-C-E

    2  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.