green eye
8Pages

Two gang PIR Dimmer GI2DPC GI2DPT Part no. > Replaces a standard light switch or dimmer > Night light mode* > Scene setting and soft on/off* > *only available using remote handset COMPATIBLE LAMPS INCOMPATIBLE LAMPS > Mains tungsten GLS filament or halogen lamp Min 60W per output Max 150W per output Low voltage halogen with transformer Min 60W per output Max 150W per output Transformer must be suitable for leading edge dimming Linear fluorescent Standard compact fluorescent (CFL) Or low energy lamps Or CFL dimmable lamps 2D fluorescent size="-2">

Compatible with all BS4662 dimensions back boxes. Remove top and bottom lugs if fitted. Use the extender if there is less than 25mm free space. REMEMBERput the wires through the extender before connecting > 25mm Location It is important to locate the detec-tor so that any occupants fall within the detection zone shown on the diagram. Do not block the sensor with a door or other object. Do not install above a radiator or other heat source. Avoid direct sunlight entering the sensor. This product should be installed in accordance with the current IEE wiring regulations. If in doubt consult a...

1 way switching If the lights are controlled from one location only, wire as in the diagram. The diagram shows a single output being used for two gang switching simply duplicate using the other output. May have red or brown sleeve > 1 2 1 2 1 2 2 way switching Where lighting is switched from more than one location, this unit can be used with another single gang light switch. N.B. do not use with another dimmer switch. Depending on the installation, wire using one of the diagrams below. > May have red or brown sleeve May have red or brown sleeve >

Short press left or right lights on output 1 or 2 Long press left or right חlights dim up output 1 or 2 Double clickextends time period to 2 hours and flashes locator. Useful when occupant is still for a long period e.g. watching television When lights on Short press left or rightחlights off output 1 or 2 Long press left or rightlights dim down output 1 or 2 When lights off Long pressחchange brightness of green-i locator > Remove front cover >

Time setting 1min30min The lights will turn off after the time setting has finished. When a movement is detected, the time starts again. Clockwise = longer delay. Recommended setting: 20 minutes living room, 10 minutes bedroom Daylight setting Auto on mode חin this mode only, if there is enough daylight the lights will not turn on auto-matically. Adjust the level using this setting. Clockwise = turn on with brighter daylight. green-i locator when there is enough daylight the locator tu rns off to save energy. Clockwise = turn on with brighter daylight. Security mode activated. 4 hours time...

turn lights on turn lights off dim up dim down adjust lights to desired level on each output Օ store scene using this sequence: set lights to preset scene number To set scene levels: set scene scene number > Soft onhow quickly the lights turn on Soft offחhow quickly the lights turn off 1 Immediate 1 Immediate 2 2 sec 2 2 sec 3 7 sec 3 7 sec 4 depends on measured light level. If it is very dark, the lights will dim the lights up slowly for maximum user comfort. 4 10 sec >

Night lightoff level, useful for chil-drenגs bedrooms. Level can be overrid-den using down button. Security modelights turn on when dark for period of time below 1 Off 1 Off 2 2 hours 2 10% 3 4 hours 3 20% 4 6 hours 4 30% button not used > Overload protection An internal temperature sensor on the device ensures that if the unit is overloaded or the ambient temperature rating is exceeded then the no permanent damage is caused to the unit. When an excessive temperature is measured, the output will dim down until the correct temperature is restored. The green-i locator will flash to warn that...

Lights turn off even though room occupied Check location of sensor՗see detection diagram Increase timing, typically 15 minutes for a living area Օ When still for a long time, double click up button Lights never turn off Is PIR activated-see switch settings Օ The lights will only turn off after no movement is detected for the time period. Is the time period set too long? The unit gets warm when on It is completely normal for the front of the unit to feel slightly warm. The lights won Ւt dim up or down or flicker Are they compatible՗see the guide on the first page? Is the total wattage higher...