strands
strands
- Dynamic Coefficient of Friction (DCOF): 0.81 (ANSI B101.3)
- Compressive Strength: >8000 psi
- IBC Flame Spread Rating: A (0-25 ft/hr)
- Freeze-Thaw Resistance: Meets ASTM C936/C1645 standards
- Weight: 7.5 lb/sq.ft for 5/8” thickness
- Thickness Tolerance: Varies, not fully gauged
- Curvature Tolerance: ± 0.5% of max tile length
- Substrate should be level within 1/8” in 10 ft and cured to a maximum of 4% moisture.
- Use Laticrete 254R Platinum Rapid adhesive and Laticrete Permacolor non-sanded grout.
- Preseal tiles with two coats of Prosoco Polishguard before installation.
- Maintain minimal grout joint of 1/16” - 1/8”.
- Expansion joints should be placed every 15 ft and at perimeters.
- Store tiles in a climatized environment, protected from damage.
- Climatize tiles for up to 48 hours in the final environment before installation.
- Handle with care to avoid chipping and damage.
- Prepare a complete installation mock-up in the final environment.
- Blend tiles from multiple crates to show tonal variations.
- Mock-up should be presealed, grouted, and cleaned before full installation.
- Clean with warm water and neutral detergent.
- Avoid harsh chemicals; use pH-neutral cleaners.
- Reapply sealer as needed to maintain protection.
- Tiles will develop a patina over time due to natural wear.
- Reapply sealer if water no longer beads on the surface.
- Use Prosoco Polishguard for sealing, applying 2-3 thin coats.
Catalog excerpts
strands technical product info cement patterned tiles strands technical product info strands cement patterned tiles are dimensionally accurate and installed with ease of tile. simply thinset, using a rapid setting adhesive equivalent to laticrete 254r platinum rapid, over a level and cured substrate. use non sanded grout like laticrete perma color grout. sealed using prosoco polishguard. sealer is available from concrete collaborative. always reference tcna guidelines for general best practices.
Open the catalog to page 1
technical summary
Open the catalog to page 2
strands technical product info our patterned cement tiles are a modern take on traditional encaustic cement tiles. our tiles are not kiln-fired or glazed but are hydraulically pressed, they will get a patina. they are composed of white portland cement, sand, natural stone and natural pigments. our process produces clean and crisp patterns and vibrant colors. tile is the finished surface of your project. it is subject to the environmental and substrate conditions. following our recommended systems and tcna standards will be instrumental to your project success. installed tile is considered acceptance...
Open the catalog to page 3
- waterproofing membrane should be employed on slab on grade or where moisture is present. consult adhesive manufacture. - follow all adhesive manufacturer preparation instructions. - walls and framed floors require cement board substrate for proper adhesion. - follow all adhesive manufacturer preparation instructions. - walls and framed floors require cement board substrate for proper adhesion. - adhesive: laticrete 254 platinum rapid. use laticrete latapoxy 300 on a steel substrate. - grout: laticrete permacolor non-sanded grout. - sealer interior: prosoco polishguard. - sealer exterior: prosoco...
Open the catalog to page 4
- ensure grout is completely dry and tiles are fully cleaned. - protect floor with ramboard and masonite to prevent damage from site debris or staining. - cleaning using mop with warm water and neutral detergent (non-acidic) - if desired, apply 1 additional coat of prosoco polishguard - allow appropriate dry time and cure time before use - caring for your encaustic cement tile is a relatively simple process to incorporate into your maintenance routine. additional steps can be implemented down the road as needed to maintain the tiles and much like a natural stone your floor can be rejuvenated...
Open the catalog to page 5
