2870 Forbs Avenue, Hoffman Estates, IL 60192 800.527.9948 | cetco.com/cps IMPORTANT: The information contained herein supersedes all previous printed versions, and is believed to be accurate and reliable. For the most up-to-date information, please visit www.CETCO.com. CETCO accepts no responsibility for the results obtained through application of this product. CETCO reserves the right to update information without notice. © 2011 CETCO | PRINTED IN THE USA ON RECYCLED PAPER | FORM:PRGTDS - 02/11 TECHNICAL DATA LINING TECHNOLOGIES | REMEDIATION TECHNOLOGIES | DRILLING SYSTEMS | BUILDING ENVELOPE CORROSION PROTECTION CONTRACTING SERVICES DESCRIPTION: PerlasticTM products by CETCO Corrosion Protection Solutions are a family of corrosion protection products for industrial applications. The chemically resistant asphalt-based formula provides excellent barrier properties to withstand many of the aggressive chemistries found on industrial sites. Perlastic Roller Grade (RG) is a thick, brushable coating used alone or in conjunction with Perlastic Spray Grade material. Perlastic RG is best used alone where corrosion protection is a requirement, and spraying is not practical due to access and/or size of application. Perlastic RG comes in 5 gallon containers. The air cured product will build about 25 wet mils thickness in one application, generating 10 mils dry film thickness. If more thickness is desired, additional applications will be required. If applying multiple coats, please wait until initial coat turns from brown to black. Perlastic products are safe and environmentally friendly since they are waterbased and contain zero volatile organic chemicals (VOCs). Perlastic products are also economical since they can be painted directly over cleansed mild rust, which reduced labor costs and eliminates the risks to health and safety with surface preparation techniques such as sand blasting. Since Perlastic is tough, flexible and easy to apply, it can be used in many different industries including mining, agriculture, waste water treatment/storage, power plants and fabricated structural steel. APPLICATIONS: Perlastic RG can be applied directly to a prepared but rusted surface and even to previously coated areas. If applying over previously painted surfaces, check for good adhesion. Adhesion testers are recommended. Perlastic RG is commonly used as a companion product to Perlastic SG. In many applications, RG can be used for “striping” corners and edges prior to spraying the SG material. Where gaps greater than 1/8” inch, it is common to use a “three coursing” method to close the gaps. This method consists of reinforcing fabric (such as Tietex 272 polyester) to bridge the gaps, applying the RG over the tape 2 inches beyond the fabric, then spraying the SG. Please refer to our technical procedures at www.cetco.com/cps for more discussion. The Perlastic line of products are formulated to provide a wide array of chemical resistance. Please request our chemical resistance guide for additional information. SURFACE PREPARATION: Perlastic can be applied to most substrates. New metal should be washed with a degreaser to remove any oils, then profiled with a wire wheel or grinder. Rusted steel should be pressure washed at 3000 psi or greater. Concrete should be power washed at 3000 psi or greater. Remove any grease/oil stains with degreaser, rinse with water. Allow to dry. Horizontal surfaces should be sealed with a concrete sealer, call for recommended products. No sealer is needed for vertical applications. CAUTION: For Industrial Use Only. Keep out of reach of children. Avoid storage below 45oF (7.2oC) and please consult the MSDS sheet before using. The Perlastic product requires eye shields, gloves and a dust mask as the coating is mildly alkaline. Keep a source of clean water nearby for eye washing. Check with Technical Services before coating for incompatibility surfaces like coal tar or other. If the surface is slick it will impair adhesion along with standing water, high humidity in an enclosed tank or the presence of oils on metal surfaces. Do not allow materials to freeze in containers. Store Perlastic at site in strict compliance with manufacturer’s instructions. When applying material below 45°F (7.2oC), contact our technical sales department. EQUIPMENT: Perlastic RG can be applied with any paint brush. For rolling, use 1/8th inch nap roller. NOTE the roller should be disposable. LIMITED WARRANTY: CETCO warrants its products to be free of defects. This warranty only applies when the product is applied by Approved Applicators PERLASTICTM RG ROLL/BRUSH-APPLIED CORROSION PROTECTION LINING PerlasticTM RG is used when spraying is not practical due to access and/or size of application limitations. It is brushable.

2870 Forbs Avenue, Hoffman Estates, IL 60192 800.527.9948 | cetco.com/cps IMPORTANT: The information contained herein supersedes all previous printed versions, and is believed to be accurate and reliable. For the most up-to-date information, please visit www.CETCO.com. CETCO accepts no responsibility for the results obtained through application of this product. CETCO reserves the right to update information without notice. © 2011 CETCO | PRINTED IN THE USA ON RECYCLED PAPER | FORM:PRGTDS - 02/11 TECHNICAL DATA PERLASTICTM RG ROLL/BRUSH-APPLIED CORROSION PROTECTION LINING trained by CETCO. The...