TECHNICAL CONSTRUCTION MANUAL COMPACK LIVING 90° system CELEGON S.r.l. - Via G. Galilei, 6 - 30035 Mirano (Venezia) - T +39 (0)41 5728404 - F +39 (0)41 5728522 www.celegon.it - [email protected] MTCL90EN - Rev. 06-06/2025

COMPACK LIVING 90° patented SMART OPENING SYSTEMS The company reserved the right to make, at any time, without prior notice, all technical changes it considers appropriate to improve the quality and the correct functionality of the products. All contents of this manual are covered by copyright. It’s forbidden even partial reproduction of text and drawings, without prior written permission of Celegon s.r.l.. Any abuse will be prosecuted according to law. All right reserved - Duplication or divulgation without autorization is strictly forbidden.

Bonetti Massimo Design COMPACK LIVING 90° patented 1. INTRODUCTION The COMPACK LIVING 90° system is part of the new generation hardware for folding hinged doors that do not use a track or hanger, similar to the tried and proven COMPACK LIVING 180° hardware (flush opening folding doors). The two COMPACK LIVING systems both use panels and doorframes that are identical in terms of dimensions and design. The 90° opening is obtained by using an innovative hinge that allows the door leaf to: move silently, use a traditional lever handle, close against stops on three sides. These functional characteristics...

COMPACK LIVING 90° patented 2. COMPATIBILITY OF THE COMPACK LIVING SYSTEM SAME DOOR LEAVES Identical size and design

COMPACK LIVING 90° patented 3. VARIANTS OF USE To get the most out of the variants illustrated on this page, see the specifications for using the COMPACK latch (see Section 7. SPECIAL COMPACK LIVING MAGNETIC LATCH). · Version 1 With symmetric door leaves By using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK. Version possible with all available items RIGHT/LEFT. · Version 2 With asymmetric door leaves with handle leaf from -100 to 0 lower By using the handle only on one side and the recessed handle on the other, is necessary...

COMPACK LIVING 90° patented 550 Part list Ref. Q.ty Description 505.1 1 Compack Living 90 system RH or LH 510 1 Central hinge lower 520.1 1 Lateral hinge lower for leaf RH or LH 530.1 1 Lateral hinge lower for jamb RH or LH 540 4 Screw TSP trx ø 4x22 550 16 Screw TSP trx ø 4x30 560 1 Invisible hinge for alignment leaves 570 1 Magnetic lock Compack Living with strikers and special square spindle (optional) 580 1 Rabbet profile (optional) (gasket NOT supplied)

SMART OPENING SYSTEMS COMPACK LIVING 90° patented Machining for rabbet profile PROS CONS - With the door open you can hardly see the machining - With the door closed, you can't see anything. Like in a swing door - Invasive machining - The finish on visible machined parts must be restored - The remaining part where the top plate is attached is a bit thin - For the same frame size, the panel is higher than a swing door

COMPACK LIVING 90° patented 3.3 Vertical section without rabbet profile SMART OPENING SYSTEMS HFM = Wall Hole Height HP = Passage Dimension HA = Leaf Height Part list

SMART OPENING SYSTEMS 3.4 Vertical section with rabbet profile COMPACK LIVING 90° patented HFM = Wall Hole Height HP = Passage DimensionHA = Leaf Height Part list

COMPACK LIVING 90° patented __ 3.5 Horizontal section left door Example of Left Door (Right door is symmetric) SMART OPENING SYSTEMS LFM = Wall Hole Width LS = Door Jamb Opening

COMPACK LIVING 90° patented SMART OPENING SYSTEMS 3.6 Dimensional diagram of the door - symmetric leaves Wall Hole Width Passage Dimension Encumbrance in opening Maximum lateral space requirement when opening door # with leaves thickness 40 Version 1 - symmetric leaves LP=LFM -198 # open door Example of Left Door Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

COMPACK LIVING 90° patented HCaeGON SMART OPENING SYSTEMS 3.7 Dimensional diagram of the door - asymmetric leaves Handle leaf from -100 to 0 lower Version 2 - asymmetric leaves (handle leaf from -100 to 0 lower) LFM = Wall Hole Width V = Maximum lateral space requirement when opening door

COMPACK LIVING 90° patented SMART OPENING SYSTEMS Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

SMART OPENING SYSTEMS COMPACK LIVING 90° patented 4.1 Single opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 90° system foresee a minimum wall opening (LFM) of 700 mm with symmetric leaves and of 650 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric and asymmetric leaves is 1100 mm. For intermediate measurements the handle leaf (version with asymmetrical door leaves) can be shortened. (*) Cases of incompatibility with COMPACK LIVING 180°.

COMPACK LIVING 90° patented SMART OPENING SYSTEMS 4.2 Dimensional diagram of the double opening door Dimensional example Attention: you need to use two hardwares COMPACK LIVING, one right and one left. hinge leaf handle leaf handle leaf hinge leaf LFMD = Double Wall Opening Width ESD = External Jamb Double (LFMD-23) LSD = Light Jamb Double (LFMD-103) LPD = Width Passagge Double Door Leaf (LFM -296 #)

COMPACK LIVING 90° patented HCaeGON SMART OPENING SYSTEMS 4.3 COMPACK LIVING 180° - 90° combination possibilities on double doors Possible combinations using the same components in wood

COMPACK LIVING 90° patented SMART OPENING SYSTEMS 4.4 Double opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 90° system foresee a minimum wall opening (LFM) of 1320 mm with symmetric leaves and of 1120 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric and asymmetric leaves is 2120 mm. For intermediate measurements the handle leaf (version with asymmetrical door leaves) can be shortened. (*) Cases of incompatibility with COMPACK LIVING 180°.