TECHNICAL CONSTRUCTION MANUAL COMPACK LIVING 180° system CELEGON S.r.l. - Via G. Galilei, 6 - 30035 Mirano (Venezia) - T +39 (0)41 5728404 - F +39 (0)41 5728522 www.celegon.it - [email protected] MTCL180EN - Rev. 12-05/2025

SMART OPENING SYSTEMS COMPACK LIVING 180° patented The company reserved the right to make, at any time, without prior notice, all technical changes it considers appropriate to improve the quality and the correct functionality of the products. All contents of this manual are covered by copyright. It’s forbidden even partial reproduction of text and drawings, without prior written permission of Celegon s.r.l.. Any abuse will be prosecuted according to law. All right reserved - Duplication or divulgation without autorization is strictly forbidden.

Bonetti Massimo Design COMPACK LIVING 180° patented 1. INTRODUCTION The COMPACK LIVING 180° system opens up new possibilities in interior design. Thanks to its reduced space requirements, silent operation and acoustic insulation properties, COMPACK LIVING 180° offers an alternative to traditional swing doors, doors that slide into or along the wall, accordion doors, and rototranslating doors. COMPACK LIVING 180° is also used in movable walls, closets and wardrobes. The COMPACK LIVING 180° system, installed between the top edge of the leaf and the lintel, makes it possible to confine the movement...

COMPACK LIVING 180° patented 2. COMPATIBILITY OF THE COMPACK LIVING SYSTEM SAME DOOR LEAVES Identical size and design

COMPACK LIVING 180° patented 3. USE VARIANTS To get the most out of the variants illustrated on this page, see the specifications for using the COMPACK latch (see Section 7. SPECIAL COMPACK LIVING MAGNETIC LATCH). · Version 1 Symmetric door leaves By using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK. Version possible with all available items RIGHT/LEFT. · Version 2 Asymmetric door leaves with handle leaf from -50 to 0 lower By using the handle only on one side and the recessed handle on the other, is necessary to apply the...

COMPACK LIVING 180° patented 550 Part list Ref. Q.ty Description 500.1 1 Compack Living system RH or LH 510 1 Central hinge lower 520.1 1 Lateral hinge lower for leaf RH or LH 530.1 1 Lateral hinge lower for jamb RH or LH 540 4 Screw TSP trx ø 4x22 550 16 Screw TSP trx ø 4x30 560 1 Invisible hinge for alignment leaves 570 1 Magnetic lock Compack Living with strikers and special square spindle (optional) 580 1 Rabbet profile (optional) (gasket NOT supplied)

SMART OPENING SYSTEMS COMPACK LIVING 180° patented Machining for rabbet profile PROS CONS - With the door open you can hardly see the machining - With the door closed, you can't see anything. Like in a swing door - Invasive machining - The finish on visible machined parts must be restored - The remaining part where the top plate is attached is a bit thin - For the same frame size, the panel is higher than a swing door

COMPACK LIVING 180° patented 3.3 Vertical section without rabbet profile SMART OPENING SYSTEMS HFM = Wall Hole Height HP = Passage Dimension HA = Leaf Height Part list

SMART OPENING SYSTEMS 3.4 Vertical section with rabbet profile COMPACK LIVING 180° patented HFM = Wall Hole Height HP = Passage DimensionHA = Leaf Height Part list

COMPACK LIVING 180° patented __ 3.5 Horizontal section left door Example of Left Door (Right door is symmetric) SMART OPENING SYSTEMS LFM = Wall Hole Width LS = Door Jamb Opening

COMPACK LIVING 180° patented SMART OPENING SYSTEMS (**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

COMPACK LIVING 180° patented HCaeGON SMART OPENING SYSTEMS 3.7 Dimensional diagram of the door - asymmetric leaves (Version 2) Handle leaf from -50 to 0 larger Version 2 - asymmetric leaves (handle leaf from -50 to 0 larger) LFM = Wall Hole Width IL Example of Left Door Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES) Version 2 - asymmetric leaves

COMPACK LIVING 180° patented SMART OPENING SYSTEMS 3.8 Dimensional diagram of the door - asymmetric leaves (Version 3) Handle leaf from 0 to +200 lower This variant also allows using a double handle or a double knob with a traditional lock, when the door's protrusion allows this. LFM = Wall Hole Width Example of Left Door Version 3 - asymmetric leaves (handle leaf from 0 to +200 lower) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

SMART OPENING SYSTEMS COMPACK LIVING 180° patented 4.1 Single opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 700 mm with symmetric leaves and of 650 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric leaves is 1100 mm. For measuremnts of LFM larger than 1100 mm is necessary to increase the dimensions of the handle door leaf. Summary dimensions for single opening door

COMPACK LIVING 180° patented SMART OPENING SYSTEMS Attention: you need to use two hardwares COMPACK LIVING, one right and one left. hinge leaf handle leaf handle leaf hinge leaf LFMD = Double Wall Opening Width ESD = External Jamb Double (LFMD-23) LSD = Light Jamb Double (LFMD-103) LPD = Width Passagge Double Door Leaf

COMPACK LIVING 180° patented 4.3 COMPACK LIVING 180° - 90° combination possibilities on double doors SMART OPENING SYSTEMS Possible combinations using the same components in wood

COMPACK LIVING 180° patented SMART OPENING SYSTEMS 4.4 Double opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 1320 mm with symmetric leaves and of 1220 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric leaves is 2120 mm. For measuremnts of LFM larger than 2120 mm is necessary to increase the dimensions of the handle door leaf. Summary dimensions for double opening door