Celegon - Technical Manual Compack Living 180° - EN
36Pages

TECHNICAL CONSTRUCTION MANUAL COMPACK LIVING 180° system CELEGON S.r.l. - Via G. Galilei, 6 - 30035 Mirano (Venezia) - T +39 (0)41 5728404 - F +39 (0)41 5728522 www.compackliving.com - info@compackliving.com MTCL180EN - Rev. 10-05/2020

COMPACK LIVING 180° patented HCCICGON SMART OPENING SYSTEMS CONTENTS The company reserved the right to make, at any time, without prior notice, all technical changes it considers appropriate to improve the quality and the correct functionality of the products. All contents of this manual are covered by copyright. It’s forbidden even partial reproduction of text and drawings, without prior written permission of Celegon s.r.l.. Any abuse will be prosecuted according to law. All right reserved - Duplication or divulgation without autorization is strictly forbidden.

Bonetti Massimo Design COMPACK LIVING 180° patented 1. INTRODUCTION The COMPACK LIVING 180° system opens up new possibilities in interior design. Thanks to its reduced space requirements, silent operation and acoustic insulation properties, COMPACK LIVING 180° offers an alternative to traditional swing doors, doors that slide into or along the wall, accordion doors, and rototranslating doors. Furthermore, COMPACK LIVING 180° may be applied to moveable walls and closets. The COMPACK LIVING 180° system, installed between the top edge of the leaf and the lintel, makes it possible to confine...

COMPACK LIVING 180° patented 2. COMPATIBILITY OF THE COMPACK LIVING SYSTEM SAME DOOR LEAVES Identical size and design

COMPACK LIVING 180° patented 3. USE VARIANTS To get the most out of the variants illustrated on this page, see the specifications for using the COMPACK latch (see Section 7. SPECIAL COMPACK LIVING MAGNETIC LATCH). · Version 1 Symmetric door leaves By using the handle only on one side and the recessed handle on the other, is necessary to apply the magnetic lock COMPACK. Version possible with all available items RIGHT/LEFT. · Version 2 Asymmetric door leaves with handle leaf from -50 to 0 larger By using the handle only on one side and the recessed handle on the other, is necessary to apply...

COMPACK LIVING 180° patented Part list Q.ty Description 1 Compack Living system RH or LH 1 Central hinge lower 1 Lateral hinge lower for leaf RH or LH 1 Lateral hinge lower for jamb RH or LH 4 Screw TSP trx ø 4x20 16 Screw TSP trx ø 4x30 1 Invisible hinge for alignment leaves 1 Magnetic lock Compack Living with strikers and special square spindle (optional) MTCL180EN - Rev. 10-05/2020

SMART OPENING SYSTEMS COMPACK LIVING 180° patented HFM = Wall Hole Height HP = Passage DimensionHA = Leaf Height (*) Leaf/track cover moulding thickness ratio Part list

COMPACK LIVING 180° patented __ 3.3 Horizontal section left door HCaeGON SMART OPENING SYSTEMS Part list LFM = Wall Hole Width LS = Door Jamb Opening

COMPACK LIVING 180° patented SMART OPENING SYSTEMS (**) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

COMPACK LIVING 180° patented HCaeGON SMART OPENING SYSTEMS 3.5 Dimensional diagram of the door - asymmetric leaves (Version 2) Handle leaf from -50 to 0 larger Version 2 - asymmetric leaves (handle leaf from -50 to 0 larger) LFM = Wall Hole Width IL Example of Left Door (Right door is symmetric) Upper hardware seat diagram (see chapter 4. DIMENSIONAL SUMMARIES) Version 2 - asymmetric leaves

COMPACK LIVING 180° patented SMART OPENING SYSTEMS 3.6 Dimensional diagram of the door - asymmetric leaves (Version 3) Handle leaf from 0 to +200 lower This variant also allows using a double handle or a double knob with a traditional lock, when the door's protrusion allows this. LFM = Wall Hole Width Version 3 - asymmetric leaves (handle leaf from 0 to +200 lower) Hinge leaf and handle leaf widths are calculated with a reciprocal distance of 1 mm.

HCaeGON SMART OPENING SYSTEMS COMPACK LIVING 180° patented 4. DIMENSIONAL SUMMARIES 4.1 Single opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 700 mm with symmetric leaves and of 650 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric leaves is 1100 mm. For measuremnts of LFM larger than 1100 mm is necessary to increase the dimensions of the handle door leaf. Summary dimensions for single opening door

COMPACK LIVING 180° patented HCaeGON SMART OPENING SYSTEMS 4.2 Dimensional diagram of the double opening door Dimensional example Attention: you need to use two hardwares COMPACK LIVING, one right and one left. hinge leaf handle leaf handle leaf hinge leaf LFMD = Double Wall Opening Width ESD = External Jamb Double (LFMD-23) LSD = Light Jamb Double (LFMD-103) LPD = Width Passagge Double Door Leaf

COMPACK LIVING 180° patented 4.3 COMPACK LIVING 180° - 90° combination possibilities on double doors HCaeGON SMART OPENING SYSTEMS Possible combinations using the same components in wood

COMPACK LIVING 180° patented HCaeGON SMART OPENING SYSTEMS 4.4 Double opening door The following form is a summary all of possible realizable dimensions with the measurements. The COMPACK LIVING 180° system foresee a minimum wall opening (LFM) of 1320 mm with symmetric leaves and of 1220 mm with asymmetric leaves. The maximum wall opening (LFM) with symmetric leaves is 2120 mm. For measuremnts of LFM larger than 2120 mm is necessary to increase the dimensions of the handle door leaf. Summary dimensions for double opening door

HCaeGON SMART OPENING SYSTEMS COMPACK LIVING 180° patented 4.5 Dimensional drawing for a 3-leaf single door Maintaining the same dimensional characteristics as in the previous tables, a third leaf can be added by connecting it to the handle leaf by means of hinges, thus obtaining very wide openings with the open doors occupying a very small space. Dimensional example with symmetrical leaves To block the leaf, you can use a traditional sliding bolt or magnet, or the magnetic unlocking system "Push&GO EVO" (see pages 17-18-19) To keep the doors together, two magnets can be inserted in the...