Universal Primer - 50600
1Pages

PRODUCT SPECIFICATION 150 DASCOMB ROAD, ANDOVER, MA 01810 | 978.623.9980 | 800.225.1141 | Fax: 800.533.6788 UNIVERSAL PRIMER 50600 PRODUCT SPECIFICATIONS: Inferior or Exterior Type: 100% Acrylic Laiex Exposure: Interior or Exterior PRODUCT DESCRIPTION: Specular Gloss! 15 @ 6QO ±5 Universal Primer is a quick drying, high performance 100% acrylic latex interior/exterior primer formulated to block most bleeding type stains while sealing porous surfaces for excellent holdout and good adhestion to prop- erly prepared hard and glossy surfaces. This primer hides many common stains such as crayon, graffiti, greasy S°llds ** Wel9hl! 43-8 % ±2 spots, water stains, rust, smoke stains, cedar and redwood bleed. RECOMMENDED USE: Dry r,im Thickness: 1.5 mils Wallboard, plaster, sheetrock, masonry, wood, concrete, galvanized metal, plastic laminates, vinyl wall cover- Vlscoslly @ 77 °F" 95 KU + 5 ings, under wall coverings as well as previously painted surfaces. Maximum VOC" 100 g/liter APPLICATION* Flash Pi °F: Non-combustible WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS Thinner: Water TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY Clean Up: Soap & Water IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to AVAILABLE COLORS AND BASES' protect yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to www.epa.gov/lead. Surfaces to be primed must be clean, dry, and free of dust, mildew, dirt, grease, wax, loose paint, or any other contaminant that may inhibit good adhesion. Wash glue size off plaster or other surfaces from which wallpaper has been removed. Do not apply over calcimine or other water soluble paints. AVAILABLE PACKAGE SIZES: Fill nicks, holes and voids with appropriate patching material. New plaster and masonry surfaces must be fully Quart Gallon 5 Gallon cured before priming. Wash new plaster with clean water, rinsing rags or sponges frequently. Sanding is not (Weight Per Gallon: 10.4 lbs. ± .5 lb) required for properly and thoroughly cleaned hard or glossy surfaces, but abrasion of the surface will increase adhesion of this product. Do not sand plaster until after the surface is primed. Tape joints on sheetrock should DRYING TIMES: be sanded smooth, with care being exercised not to abrade the surrounding paper backing. Wire brush rusted areas to remove loose rust. Plasticizers must be thoroughly removed from vinyl wall coverings with mineral spir- its and a clean cloth that is changed frequently. Before priming stained areas, remove as much of the stain as ^o Handle: 4 hrs. possible by washing, sanding or scraping. Some stains may require two coats. If an active stain discolors this To Reeoal: 2 hrs. primer, apply the finish coat to a small area to see if the stain is "locked" into the primer. If not, re-prime. (@ 70-77 °F, 50% R.H.) ARCHITECTURAL SPECIFICATIONS: SURFACE SPREAD RATE: Plaster, Wallboard, Sheetrock, Concrete, Masonry, Galvanized Metal Wood, Aluminum: 1 coat Universal Primer 50600 1 or 2 coats any California Paints Latex, Alkyd or Urethane in desired finish. Porous: 175-225 s.f./gal. (Spray Application is 50% of above) Do not add solvents, oils or colors in oil, or mix with other paint types. Low temperature, high humidity, or inadequate ventilation will slow drying times. Application on hard non-porous surfaces requires a minimum of 2 hours dry time before recoating. Stearate containing clear finishes, shellacs and any clear finish that has BrUsh ! SYn'hetic. Nylon or Polyester been waxed, polished or has surface soap residue can present adhesion problems for any coating. Apply a test Roller : 3/8 Nap Synthetic Fiber area of primer over any clear finish and test for adequate adhesion after one week of curing. Universal Primer Airless Spray : .017 to .019 Tip is ready-to-use as it comes from the container, but can be thinned sparingly with water if necessary. Air and surface temperature should be 50°F (10°C) or higher during application and drying time. Keep from freezing. Difficult stains may require the use of Stain Killing Primer 20700 Sealer. SAFETY INFORMATION: Keep out of reach of children. Do not take internally. Close container after each use. Protect from freezing.