Catalog excerpts
External Applications Balustrades Balustrades made of CELLON®-panels General Information Individual panel segmentation within the following design sizes: Our CELLON®-panel is a Compact High-Pressure Laminate Panel (HPL) consisting of 70% cellulose sheets and 30% phenolic resin. weather-resistant material is ideally suited for external applications such as balcony panel. The unprocessed boards are manufactured exactly as required for each individual project using laser technology. The panels are thus pre-cut to the exact dimensions (incl. drill holes) and with the desired perforations for the specific site. The panels are coated after cutting. Depending on the perforation and the distance between the fixing points, 8 or 10 mm thick panels are used.
Open the catalog to page 1The Advantages at a Glance The unlimited selection of perforation patterns and colours provide a large variety of design options, this way the degree of transparency can be selected freely Precise laser cut allowing for free contour and soft edges according to the submitted CAD data Over 100 perforation available from Bruag Option of custom patterns according to your CAD template at no additional cost Perforations can run smoothly across multiple panels Wide choice of colours (coating according to NCS S Edition 2, RAL, Bruag Alu or IGP) Special colours on request Moisture-resistant,...
Open the catalog to page 2Design Notes Design Dimensions for Balustrades made of CELLON® Panels Design Dimensions for Top-Mounted Balustrades Design Dimensions for Front-Mounted Balustrades Design Dimensions for Balustrades made of CELLON® Panels Position Minimum Distance Maximum Distance Recommended Unit Distance Edge without perforation Distance from drill hole to edge Horizontal drilling distance Vertical drilling distance (1) Vertical drilling distance (2)
Open the catalog to page 3Material: A2 stainless steel Length: 32 mm Nominal Diameter of Screw: 4.8 mm Head Diameter: 16 mm Drive: SW7 The diameter of the drill holes should be designed to be 8 mm on the upper horizontal, on the lower and, if present, be 10 mm on the centre horizontal. The panels are fixed by means of “self-tapping façade screws with hexagonal head and washer”, diameter 4.8 mm, supplied by Bruag. Alternatively, rivets or other screws may be used. In general, it is important that the drill holes are larger in diameter than the screw diameter, so that the panel can expand easily. These must be...
Open the catalog to page 4Details - Top-Mounted Balustrades Section Front Elevation
Open the catalog to page 5Details - Front-Mounted Balustrades Section Front Elevation
Open the catalog to page 6Details End Handrail Variant 1 The upper border of the panel and handrail needs to be covered. This cover helps to protect the edge of the panel. This can be done by bonding simple angled section to it. Concealed Option End Handrail Variant 2 Alternatively, you can also clamp an L-profile between panel and metal frame before screwing the plate. Like this, the upper edge of the panel is also covered. Corner Connection The panel is bonded into the bottom section. Drainage must be ensured. Balustrade with Top-Mounted Handrail Corners are usually butted up joints. An alternative configuration...
Open the catalog to page 7Guarding Floor-To-Ceiling Windows Guarding Floor-To-Ceiling Windows with Circumferential L-Section Guarding Floor-To-Ceiling Windows with Circumferential Square Tube
Open the catalog to page 8Balustrade Alternatives The perforations shown below are examples only. You can find more design options in our perforation collection. Balustrade front-mounted without handrail Perforation 50653 Balustrade top-mounted without handrail Perforation 10100 Balustrade front-mounted separated Perforation 50112
Open the catalog to page 9Balustrade front-mounted without handrail Perforation 50100 Balustrade front-mounted with handrail Perforation 10210 adapted Balustrade top-mounted with handrail Perforation 50050
Open the catalog to page 1011 Bruag AG Bahnhofstrasse 8 8594 Güttingen Schweiz info@bruag.ch www.bruag.ch
Open the catalog to page 11All Bruag Design Factory AG catalogs and technical brochures
-
Innovative Cladding Elements
25 Pages
-
Ventilated Façade Solutions
9 Pages
-
Noise-Virus-Catcher®
1 Pages
-
Zeitgeist 2016
2 Pages
Archived catalogs
-
CELLON® design
8 Pages
-
Acoustics Elements
3 Pages
-
Brève Information CELLON®
2 Pages
-
Zeitgeist 2015
4 Pages