Specification 1. Power supply: 85~230VAC, 50/60 Hz 2. Temperature setting range: 5-35°C 4. Temperature control Accuracy: ± 1 °C 6. Remote Sensor Type: NTC10K, B=3950 7. Storage temperature: -20C~60C, Operating temperature: 0~50°C 12. Installation type: Flush mounting, Hole pitch: 60mm =Menu; '/Confirm or On/Off; — Decrease; + Increase ON/OFF: Press power button ^ to switch ON and OFF thermostat. Temperature Setting: Press “ —” to reduce or press “+” to raise temperature Clock Power on thermostat, press “:=” for 2 times until the date icon flashes Power on thermostat, press “:=” 7 times to entry the programmable settings 4, press “:= again and use — + to change temperature setpoint 5, Press “:=” to edit other date and other events value 6, Press “v/” to save and exit *Please note: when the schedule is set to be Weekday/weekend(Feature 03= 52), in the App only Monday and Saturday settings work, Monday means Weekday schedule; Saturday means Weekend schedule . The hold function will keep the set temperature at hold temperature all the time to override the programmable function all the time. Enable the hold: Press 4~ and — to change the set temperature, then hold and press the v' till you see the hold text shows on the right-top corner. Disable the hold: Under the backlight is off state, hold and press the v7 till you see the hold text disappear from the right-top corner. Hold and press key+ and —for 10s to configuration Key lockout function is enable) Home mode: Under the backlight is on state, seconds till the icon ^ appears. Away mode: Under the backlight is on state, seconds till the icon O* appears. Press the key := “plane” icon shows on the screen, Press —or + to adjust the holiday days. For example 5 days, and you set the setpoint to 28C, so the thermostat will keep 28C for 5 days Press key 'Z to turn off thermostat Hold and press for 7 seconds till there are two big numbers display on screen. The middle big number is the feature settings , the right-top small number is the feature number, you can press key to select features and press —or + to adjust each feature settings , below table is the configuration list setting details. 1, Power Failure Recovery: Thermostat status after the failure power recovery 5- Differential: The thermostat will switch on the heating device when the differential temperature between setpoint and room temperature is higher than this value 8- Floor Limit Temperature: if floor sensor temperature is higher than this limit value, thermostat will cut off the heating, and floor icon ft flashes on the screen means the floor temperature is too high. When the floor temperature drops to normal value, the ft will disappear and thermostat will keep running the heating device 9- Sleep mode: This function is only available on “Evening(event 4) under programmable mode, means setpoint decrease 1C every hour during night, 10- Frost Protection Temperature: the thermostat will take this value as setpoint even the thermostat is switch OFF(with power on), the thermostat will turn on the heating device with screen as blank. 12-Clock Sync: set thermostat sync internet time for the product with Wifi function only 14- Output Delay: Thermostat will keep running the heating device after room temperature reaches the setpoint 00: thermostat build in sensor only 01: External sensor only to instead of internal sensor 02: Floor sensor only: thermostat only show floor sensor temperature, and thermostat turn on/off heating device according to the floor sensor temp. setpoint 03: Internal sensor for room temperature, and floor temperature for floor temperature protection 04: External air sensor & Floor protection sensor The device is considered electronic equipment for disposal in terms of the applicable local Directive and may not be disposed of as domestic garbage. --Device disposal through channels provided for this purpose. --Comply with all local &

1, Basic wiring diagram with switch live for heat item. 2, Volt free switching for heat item Thermostat operation: 1, Turn off thermostat by press ^ 2, Press and hold H- key until countdown number appears in the middle t he screen. your thermostat WiFi icon is rapidly blinking 3, Connecting to WB10 Wiring Centre App operation: 1. Press "Add Device" or "+" in the upper right corner of the app 2. add the device under the small appliance section 3. select the device type "Thermostat WiFi" , 4. fill in your router’s password, and clicking the "Confirm the indicator is blinking” Then there are two...