BC103S-2AE-24 Series User Manual This Fan coil thermostats are widely used in all commercial and residential buildings room temperature control, accuracy control provides you comfortable environment, and have the effect of saving energy and reducing up to 30% power consumption. This universal thermostats work with: ^ 2-pipe fan coil unit ^ EC Motor Fan ^ 0-10V valve ^ Timer/Programmable(model No. with T Only) ^ Dry contact for window or door, Hotel card holder ^ External sensor for air temperature or pipe temperature 2. Temperature setting range: 5-35°C 4. Temperature control Accuracy: ± 1°C 6. Valve Control: 0-10V valves 7. Remote Sensor Type: NTC10K 8. Communication: Modbus 4800,9600,19200bps baud rate 9. Dry contact: for window, door or hotel card holder 10. Storage temperature: -20C~60C, Operating temperature: 0~50°C 15. Installation type: Surface mounting, Hole pitch: 60mm User Guide: ON/OFF: Press power button to switch ON and OFF thermostat. Temperature Setting: Press “^” to reduce temperature, press “A” to raise temperature Mode: Press “M” to change mode between Cool tfc, Heat • and Ventilation ❖ mode will be confirmed by pressing other button or automatically after 6 seconds Fan: Control EC Motor fan with 0-10V output, user can set up the voltage output by flowing steps: Switch off the thermostat and press “M” and “'"'”5 seconds to enter parameter setting menu, press the “M” or “'S'” to change the item, and press to For example: The value is 40, The output voltage is 4V. (40*10%=4V). Item 07: Low Speed; (Range from 11 ~40 Default=40) Item 08: Med Speed; (Range from 41~70 Default=70) Item 09: High Speed; (Range from 71 ~99 Default= 90) Press power button “O” or wait 30S to exit and save all settings Valve: control 0-10V valve, user can set up the voltage output by flowing steps: Switch off the thermostat and press “M” and 5 seconds to enter parameter setting menu, press the “M” or to change the item, and press to Item 01: Heating mode KP, Range from 1 ~99, Default=10 Item 02: Cooling mode KP, Range from 1~99, Default=10 Item 03: Sampling time, Range from 1~99,(s), Default=20 Item 04: KI, Range from 1~99, Default=1 Item 05: kD, Used Item 06: Span, Range from 1~99, Default=5 Warning: the value above must set by specialized installation person!! Backlight: Any key press will activate the backlight. Backlights will timeout 6 seconds after last key press. Keypad Lockout: (ONLY available when Item 11 set to 1/2/3): Press “^”and “A” for 3 seconds to lock the buttons and press “^”and “A” for 3 seconds to unlock. Clock(Only for the model number with T): Power on thermostat, press “M” for 3 seconds 1, the symbol hour flash, press ^or ^ to adjust hour 2, press “M” key, minute flash, press “^” or “A” to adjust minute 3, press “M” key, week flash, press “^” or “A” to adjust week Press power button “O” or wait 30S to exit and save all settings Timer on/off(Only for the model number with T): Repeat the Clock steps 1~4 above 1, Timer on and hour flash, press “^” or “A” to adjust hour 2, press “M” key, minute flash, press “^” or “A” to adjust minute 3, press “M” key, Timer off and hour flash, press “^” or “A” to adjust hour 4, press “M” key, minute flash, press “^” or “A” to adjust minute 5, press “M” or wait 6 seconds to confirm Note: This function only acts once and valid on current day. Press power button “O” or wait 30S to exit and save all settings Programmable(Only for the model number with T): Power on thermostat, press “M” and for 3 seconds 2, Press “^”and “A” to set start hour 3, Press “M” and use “^” “A” to set start minute 4, Press “M” and use “^” “A” to set desired temperature 5, Press “M” to enter event 2/3/4 and repeat step 2~4 6, Press “M” to edit “Sat & Sun” and repeat step 1~5 7, Press “M” or wait 6 seconds to confirm all the settings above Press power button “0” or wait 30S to exit and save all settings Parameter Settings: Switch off the thermostat and press “M” and “■*■”5 seconds to enter parameter setting menu, press the “M” or to change the item, and press'^ -Mo change the value, press power button “O” or wait 30S to exit and save all settings Table Explanation: 1- Selectable System Type: control 2-pipe fan coil unit only 2- Auto Mode: you can set your 2-pipe system running as manual or auto season changeover 3- Sensor Type: 1: Internal sensor only. 2: external sensor only 3: the external sensor attaches to water pipe for measuring the water pipe temperature to change mode between Heat and Cool automatically, this function is only available under 2-pipe Fan coil (Option 1=0) and auto system (Option 2=1) at the same time System works in cooling mode if the water temperature is less

4-Fan Control: when the room temperature reaches setpoint, you can set the fan stop running or continuous blowing 5-Unoccupied Status: when the hotel card is pulled out, the unoccupancy status will be: 0: no output; 1: thermostat will work in energy saving mode with setback setpoint, fan will run at low speed Mount the room thermostat on the conduit box. Do not mount on a wall in niches or bookshelves, behind curtains, above or near heat sources. Mount about 1.5 m above the floor 7- Display Temperature adjustment: calibrate the room temperature by the range from -4C to 4C 8-Dead Band: the cool/heat...