:DEN THE BELDEN BRICK COMPANY THE FOUNDATION TO BUILD YOUR NEXT MASTERPIECE

R VALUE 6 INCH THRU-WALL 8 INCH THRU-WALL Hollow ASTM C 652 R =. 95 Hollow ASTM C 652 R = 1.10 These two values are calculated using the dual path procedure outlined in Brick Industry Association (BIA) Technical Notes 4. (Path A was through the face shells and webs, Path B was through the face shells and cells. A weighted average was then determined for each path and added together.) Higher value may be obtained by calculating the walls’ U-Value, taking into account outside and inside air films. HOLLOW SOLID 6 INCH THRU-WALL 5-5/8 x 3-5/8 x 15-5/8” Unit Weight = 16 lbs. Decibles 41 50 FIRE...

6 INCH 8 INCH 8 INCH 12 INCH BRICK CMU BRICK CMU • Modest Loading • Wind at 20psf • Comparable Grout and Reinforcing • CMU f’m @ 1500 psi • Clay f’m @ 3500 psi From a cost comparison standpoint, we are comparing installed costs of various Reinforced Brick Masonry (RBM) and Concrete Masonry Unit (CMU) single wythe systems. In comparing 6” TTW brick and 8” half high CMU, in a days time, a mason and tender will install approximately 350 CMU. In that same time, 365 brick would be installed. Productivity differences are due to unit size and weight. Similar productivity differences by other size TTW...

ISOMETRIC VIEW II I II II II II I II II I_ _ _ _uiii~i~ii~i~ii_ _ _ _~luil~ II II II II III ~~~iiiwi FRONT VIEW TOP VIEW ISOMETRIC VIEW FRONT VIEW 7-5/8" BED BOND BEAM SIDE VIEW

ISOMETRIC VIEW iiiiiiii ~~----~~~----~~ FRONT VIEW ISOMETRIC VIEW FRONT VIEW 13/4 in [44 mm) 5-5/8" BED BOND BEAM (39.1% VOID) SIDE VIEW

FRONT VIEW ISOMETRIC VIEW III I II IIII IIII IIII '" FRONT VIEW ISOMETRIC VIEW SIDE VIEW

FRONT VIEW ISOMETRIC VIEW ISOMETRIC VIEW FRONT VIEW 5-5/8" BED BOND BEAM (39.1% VOID)

24 Hour Submersion in Cold Water (%) 0.78 1.03 1.51 1.72 0.77 1.16 5 Hour Submersion in Boiling Water (%) 1.11 1.32 2.23 2.09 0.97 1.54 Saturation Coefficient (Ratio of 24H to 5H) 0.71 0.78 0.68 0.82 0.79 0.75 COMPRESSIVE STRENGTH PSI MPa AVERAGE % VOID 24 Hour Submersion in Cold Water (%) 2.76 2.82 2.79 3.16 2.75 2.85 5 Hour Submersion in Boiling Water (%) 3.31 3.40 3.33 3.58 3.26 3.38 Saturation Coefficient (Ratio of 24H to 5H) 0.83 0.83 0.84 0.88 0.84 0.85 COMPRESSIVE STRENGTH PSI MPa...

TEST DATA THRU-WALL ALL SHALE 6 x 4 x 16 ABSORPTION 24 Hour Submersion in Cold Water (%) 5 Hour Submersion in Boiling Water (%) Saturation Coefficient (Ratio of 24H to 5H) AVERAGE % VOID EFFLORESCENCE TEST DATA 08/19/2010 AVERAGE 5.0 MOMENT OF INERTIA (I) AND RADIUS OF GYRATION ® TABLE 8” DOUBLE MONARCH TTW HOLLOW @ 48 in OC @ 40 in OC @ 32 in OC @ 24 in OC @ 16 in OC SOLID INERTIA PER LINEAR FOOT GYRATION PER LINEAR FOOT MOMENT OF INERTIA (I) AND RADIUS OF GYRATION ® TABLE 6” MONARCH TTW HOLLOW INERTIA PER LINEAR FOOT GYRATION PER LINEAR FOOT BRICK MASONRY STRENGTH The net compression strength...

Reinforced brick masonry is not a new wall system. Reinforcing steel and grout have been used with brick masonry for over 100 years. With brick masonry's high compressive strength, reinforcing makes for an economical, highstrength wall in comparison to other reinforced masonry systems. Thru-Wall Brick offer: o Greater design flexibility. Reduced backup requirements. Reduced number of tie connections, which provides a more continuous moisture barrier. Greater seismic resistance and more ductility. Less restrictive deflection requirements of the backup structure. Reduced cost of the backup system....

The Standard of Comparison An ISO 9001:2008 Registered Quality Management System An ISO 14001:2004 Environmental Management System BeLden THE BELDEN BRICK COMPANY