FD-DA02
2Pages

{{requestButtons}}

Catalog excerpts

FD-DA02 - 1

OrangeLink FD-DA02 4 IN / 4 OUT Module – 6 units DIN rail Functional characteristics FD-DA02 is a module for the acquisition of sensors data and to command actuators devices like sirens, electrical locks, etc with the following characteristics: ♦ Can be mounted on DIN rails ♦ Data acquisition from dry contacts (ON/OFF) ♦ Data acquisition from supervised sensors managing 5 states per sensor (normal, alarm, tamper, cut circuit, short-circuit), and inject pseudo-random interference in order to prevent level detection from the outside. ♦ Able to control resistive and inductive loads up to 4 loads, from 0.3ADC (0.2 AAC) up to 2.5 ADC (1.8AAC) per channel adding optional relays) ♦ Output monitoring, with alarm generation in the event of faults ♦ Able to monitor a FD-PA01 power supply module through a suitable connection, for all the main electrical parameters including the battery effectiveness tests. ♦ Visual fault and/or alarm indication ♦ Connection to FD-BUS through an RJ45 connection ♦ Double RJ45 connector (internally in parallel) for easy reconnection to the FD-BUS. ♦ Galvanic separation of the FD-BUS backbone from the local reference ground ♦ Possibility of connecting the FD-BUS remote power supply to the local power supply through jumpers. Protection The equipment is protected against the following events: ♦ polarity reversal on the cables (RJ45) connecting to the FD-BUS ♦ voltage surge in the power supply ♦ negative voltage peaks at outputs with inductive loads Modes of Operation The FD-DA01 module is part of the Orangelink system and can perform the data acquisition functions related to the status of sensors and/or contacts, and control electrolocks and/or turnstiles. The module can operate in two different modes: ♦ In dry contact (access control) acquisition mode, the module can acquire the status data from 8 contacts. ♦ In supervised contact acquisition mode (intrusion dtection and access control), the module can acquire the status data from 4 sensors, and manage the 5 possible states (normal, alarm, tamper, cut, short-circuit). Visual indicators The FD-DA01 module can give the user indications The most common indications are as follows: by means of: ♦ Green LED, lit steadily when in operation ♦ a red LED ♦ Red LED, lit steadily in the event of an alarm and/or fault ♦ a yellow LED ♦ Yellow LED, flashes during communication (one flash per message) ♦ a green LED FD-DA02-DS-02-en.doc Pg. 1/2

Open the catalog to page 1

All Axess TMC catalogs and technical brochures

  1. MESH

    2 Pages

  2. DV3 Series

    2 Pages

  3. AX-NVR

    2 Pages

  4. GYMGEST

    6 Pages

  5. WORKFLOW

    2 Pages

  6. PRES-J

    8 Pages

  7. PTM

    2 Pages

  8. MicroAccess

    1 Pages

  9. AX GATE

    2 Pages

  10. RFID/3

    2 Pages

  11. APERIO?

    2 Pages

  12. FingerReader

    1 Pages

  13. MAX GATE

    2 Pages

  14. FD-WA01

    2 Pages

  15. FD-RAOx

    2 Pages

  16. OP-PA01

    2 Pages

  17. XAtl@s Intro

    2 Pages

  18. AX BIO

    2 Pages

  19. XPoint-Touch

    2 Pages

  20. X2

    2 Pages

Archived catalogs

  1. TRAXGATE

    2 Pages

  2. SUPERTRAX

    2 Pages

  3. ULTRAX

    1 Pages

  4. FingerTrax

    2 Pages

  5. SUPERMAX

    2 Pages

  6. RFID

    1 Pages

  7. X ATLAS

    2 Pages

  8. XPOCKET

    2 Pages

  9. FINGERREADER

    1 Pages