A system for every application Expert Manufacturer of High Performance Systems

Starting in Belgium, Atab has developed from being the market leader within Benelux into an international organisation specialising in waterproofing. Its many years of experience – with factories in Antwerp since 1911 – have firmly established Atab’s specialised technical know-how in the roofing industry. Atab is your leading expert in both the areas of consultation and the manufacture of tried and tested, durable, bituminous and synthetic roofing systems, as well as in the field of thermal insulation and durable energy-saving systems. Atab has been the European headquarters and centre of excellence...

IKO enertherm: A system for every application Product Flat roof insulation: Tapered isolation: Flat roof insulation IKO enertherm BGF IKO enertherm MG IKO enertherm ALU IKO enertherm ALU IKO enertherm ALU TG Pitched roof insulation, internal Pitched roof insulation, exterior Cavity wall insulation Wall (post-)insulation Floor insulation

Why is IKO enertherm your best bet? Good insulation makes a positive contribution to the environment • The cooling and heating of buildings causes approximately 40% of the world’s total CO2 emissions. % of energy loss with a non-insulated house 35% • The insulation of buildings is therefore the most direct and efficient solution for saving energy and reducing CO2. • In most cases, building insulation can easily be improved and/or retro-fitted. • Over 50 years, IKO enertherm has saved 100 times more energy than the intrinsic energy required for its manufacture. Raw materials and the manufacturing...

IKO enertherm: the highest efficiency per m² Comparison of weight vs. thickness 39 mineral wool IKO enertherm is lightweight insulation. The weight of the foam only amounts to +/- 32 kg/m3. Due to the low weight, the enertherm packages are easy to transport and handle. The table above clearly demonstrates that Enertherm insulation is 90% lighter than mineral wool for the same thermal resistance. Minimum board thickness, maximum efficiency IKO enertherm insulation has the highest efficiency per m². This means that, compared to other insulation materials (such as EPS, XPS and rockwool), a higher...

The best total solution for the insulation of the hot flat roof. Can be used on bituminous and synthetic roofing sheets. 1 or 2 layers, with an extremely thin PIR board: IKO enertherm ALU, BGF and MG. • Very light insulation, up to 90% less than mineral wool. • Very competitive: up to 40% less volume than other insulations for the same R value. • The area can be walked on during and after the work. • Excellent fire classification: B S2 DO. • Boards up to 3 m². IKO enertherm BGF bonded to the bituminous sub-layer with IKO pro PU adhesive. IKO enertherm BGF Innovative product with the following...

A system for every flat roof IKO enertherm BGF Coated on both sides with a bituminised glass fibre membrane, free from sand and talcum. Thermal conductivity: λD value = 0.026 W/mK if thickness ≥ 120 mm, 0,027 W/mK if thickness ≥ 80 mm and 0.028 W/mK if thickness < 80 mm. Applications • A partially flame-welded sub-layer or top layer. • A fully bonded roofing system with bituminous cold glue. • A mechanically fastened roofing system, 1 or 2 layers. • A loosely-laid, ballasted roofing system. Also available with tapering, and with a rebate on request. Dimensions Board dimensions: 600 x 1200 mm,...

Is wood an adequate insulator? Perfect humidity-proof and windproof insulation screen for your attic Wood is an insulator. To a limited extent, however. The lambda value of wood is a mere 0.17 W/Mk. This means that you require 51 cm of wood for the thermal resistance (R value 3). If you therefore insulate between the wooden rafters, you end up with a number of thermal bridges. In view of the fact that 10% of the total surface of a rafter roof consists of wood, the impact on the overall insulating capacity of the roof is quite substantial. A brief comparison: 7 cm of mineral wool between the rafters...

Perfectly-sealing edge finishing “Ultra Fit” guarantees insulating screen This innovative edge finishing offers the following advantages: • Perfect fit of the insulation boards • No energy loss • No clearance: ‘Air lock’ The ‘Ultra Fit” edge finishing is applied to IKO enertherm ALU TG and KR ALU TG, and can be used for wall cavities, floors, sarking and attics (Comfort).

The best overall solution for the exterior insulation of your roof, including sub-roof, with the IKO enertherm ALU NF, IKOFIX fasteners and IKO sub-roof. • The insulation screen without interruptions. • Ideal solution for exterior renovation. • Your interior finishing remains intact. • The “Ultra fit tongue and groove: air lock” edge finishing ensures a windproof and thermal screen without thermal bridges. • 60% thinner than the traditional structure between the rafters. • Rigid and form-stable. • Insensitive to moisture. • Fibre-free, therefore no irritation. • Very quick installation as a result...

The best overall solution for the insulation of your attic, using an ultra-thin IKO enertherm ALU TG PIR board, IKOFIX fasteners and IKO ALU tape. • Your perfect attic insulation building professionals and home-owners. • 60% thinner than the traditional structure between the rafters. • The ‘Ultra Fit’ tongue and groove edge finishing and the IKO ALU tape guarantee a windproof and thermal screen. • The rigid yet light boards are form-stable. • Fibre-free, therefore no irritation. • Insensitive to moisture; an additional moisture barrier is not required thanks to the closed cell structure and the...

The best overall solution for the (post-)insulation of your external walls, using ultra-thin, IKO enertherm ALU TG PIR boards and accessories. • Your interior finishing remains intact. • Various types of finishing are possible (wood, zinc, sidings …). • The tongue-and-groove edge finishing and the IKO tape guarantee a windproof and thermal screen. • The rigid yet light boards are form-stable. • Fibre-free, therefore no irritation. • Insensitive to moisture. • Reflective backing. • Almost 40% thinner than mineral wool, XPS or EPS for the same R value. IKO enertherm ALU TG Coated on both sides...