*myarchiexpo

Catalogs
ASTURIANA DE LAMINADOS
Double lock standing seam - Guide to detail forming

Double lock standing seam - Guide to detail forming

Product catalog summary

Introduction
This guide provides comprehensive instructions for forming standing seam details using elZinc® products, highlighting the importance of proper execution for both performance and aesthetics. It is designed to be universally understood, accommodating various regional practices through simple steps and illustrations.

elZinc®: A Quality Brand
elZinc® products surpass EN 988 and ASTM B-69 standards, utilizing high-purity zinc alloyed with copper and titanium for enhanced durability and self-healing properties, with a lifespan exceeding 100 years.

elZinc® Finishes
The elZinc range includes Alkimi and Rainbow finishes, offering diverse aesthetic options. Alkimi retains zinc's natural properties, while Rainbow provides colored finishes with added corrosion protection.

Matrix: Standing Seam Details
The guide details various seam end techniques, each with specific instructions:

Squared Foot: Suitable for angles over 3 degrees, using a nibbler to prevent splits.
Chamfered Foot: Common termination avoiding small holes, using a notcher for undercloak.
Curved Foot: Decorative but time-consuming, requiring warming in cold weather.
Swabian Foot: Easiest detail, using a punch or drill for rounded corners.
Turned Down Upstand: Suitable for short/medium upstands, requiring space behind the detail.
Straight Dog-Eared Upstand: Used for short upstands, with optional cutaways for folding.
Pinched Seam: Preferred for tall upstands, ensuring a tight seal.

Conclusion
This guide should be used in conjunction with other elZinc technical literature to ensure proper installation and longevity of zinc cladding and roofing systems.

Overview: This document serves as an installation guide for elZinc® standing seam systems, focusing on pinched seams and single lock cross welts, with step-by-step instructions emphasizing adherence to specified dimensions and angles.

Pinched Seam - DLSS I 1.2.2.03a:

Scale: 1/4
Instructions: Steps 1 to 10 outline the creation of a pinched seam, including using a flat head seaming iron and ensuring the overcloak dog-ear fold is slightly lower than the undercloak.
Key Points: Ensure overcloak folds cover the undercloak 'hole' and maintain an angle greater than 3º.

Saddled Pinched Seam - DLSS I 1.2.2.03b:

Scale: 1/2 and 1/1
Instructions: Steps 1 to 8 guide the creation of a saddled pinched seam, emphasizing correct alignment of dog ear fold lines and roof pitch.
Key Points: Maintain an angle greater than 3º and ensure printing is set to a 100% scale for accuracy.

Single Lock Cross Welt - DLSS I 2.1.1a:

Scale: 1/2 and 1/1
Instructions: Steps 1 to 12 provide guidance on forming a single lock cross welt, including the use of zinc spacers and preferred tools like folders.
Key Points: Over-bend the upstand to remove zinc spacers easily and maintain an angle greater than 25º.

Contact Information: For further assistance, contact Asturiana de Laminados, S.A. at [email protected] or visit www.elzinc.es.

Catalog excerpts

Double lock standing seam - Guide to detail forming-1

Double lock standing seam Guide to detail forming www.elzinc.es Designing with elZinc®

Open the catalog to page 1

Double lock standing seam - Guide to detail forming-2

elZinc® Installation Guide: Standing seam Index Introduction to this guide elZinc® a quality brand elZinc® a long-lasting building material elZinc® Finishes elZinc® Alkimi elZinc Rainbow® Matrix standing seam DLSS I 1.2.1.01a - Squared foot DLSS I 1.2.1.02a - Chamfered foot DLSS I 1.2.1.02b - Chamfered foot DLSS I 1.2.1.03a - Curved foot DLSS I 1.2.1.03b - Curved foot DLSS I 1.2.1.05 - Swabian foot DLSS I 1.2.1.03a - Turned down upstand DLSS I 1.2.2.02a - Straight dog-eared upstand DLSS I 1.2.2.02b - Preformed straight dog-eared upstand DLSS I 1.2.2.03a - Pinched seam DLSS I 1.2.2.03b - Saddled...

Open the catalog to page 2

Double lock standing seam - Guide to detail forming-3

elZinc® Installation Guide: Standing seam Introduction to this guide Correct execution of zinc roofing and cladding work is key to the performance of the envelope. It also contributes greatly to its aesthetic appeal. This booklet shows the forming process of some of the most commonly used details for finishing a standing seam at its foot and at its head in roofing. The process is broken down into simple steps with easy to interpret drawings, with the use of symbols and minimal text, so installers can understand the cutting and folding sequences and correctly execute the details worldwide without...

Open the catalog to page 3

Double lock standing seam - Guide to detail forming-4

elZinc® Installation Guide: Standing seam elZinc® Finishes Full of contrasts, the elZinc range of finishes is currently the widest on the market. Divided into two range of finishes - elZinc Alkimi (elZinc Natural, elZinc Slate®, elZinc Graphite®, elZinc Crystal®, elZinc Lava® and elZinc Oliva®) and elZinc Rainbow®, our rolled products are ideal for architectural roofing, architectural cladding and interior design. Available manufacturing options: • Rolling thicknesses: from 0,2 mm to 3 mm • Rolling widths: from 70 mm to 1.320 mm • Coil weights: from 50 kg to 10.000 kg elZinc Alkimi Zinc cladding...

Open the catalog to page 4

Double lock standing seam - Guide to detail forming-5

elZinc® Installation Guide: Standing seam Matrix: Standing Seam 01 DLSS I 1.2.1.01a - Squared foot DLSS I 1.2.1.02a - Chamfered foot DLSS I 1.2.1.02b - Chamfered foot DLSS I 1.2.1.03a - Curved foot DLSS I 1.2.1.03b - Curved foot DLSS I 1.2.1.05 - Swabian foot DLSS I 1.2.2.01 - Turned down upstand DLSS I 1.2.2.02a - Straight dog-eared upstand DLSS I 1.2.2.02b - Preformed straight dog-eared upstand DLSS I 1.2.2.03a - Pinched seam DLSS I 1.2.2.03b - Saddled pinched seam DLSS I 2.1.01a - Single lock cross welt DLSS I 2.1.01b - Single lock cross welt

Open the catalog to page 5

Double lock standing seam - Guide to detail forming-6

elZinc® Installation Guide: Standing seam Squared foot - DLSS I 1.2.1.01a 01 All dimensions are indicative unless specified on the drawing

Open the catalog to page 6

Double lock standing seam - Guide to detail forming-7

elZinc® Installation Guide: Standing seam Squared foot - DLSS I 1.2.1.01a 01 For correct printing, please make sure to set your printer to a 100% scale. · We recommend using a nibbler to avoid splits. All dimensions are indicative unless specified on the drawing

Open the catalog to page 7

Double lock standing seam - Guide to detail forming-8

elZinc® Installation Guide: Standing seam Squared foot - DLSS I 1.2.1.01a All dimensions are indicative unless specified on the drawing

Open the catalog to page 8

Double lock standing seam - Guide to detail forming-9

elZinc® Installation Guide: Standing seam Squared foot - DLSS I 1.2.1.01a All dimensions are indicative unless specified on the drawing

Open the catalog to page 9

Double lock standing seam - Guide to detail forming-10

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02a 01 OK > 3º Most common foot termination Alternative to DLSS 1.2.1.02b. Avoids small hole at top of chamfer All dimensions are indicative unless specified on the draw

Open the catalog to page 10

Double lock standing seam - Guide to detail forming-11

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02a 01 For correct printing, please make sure to set your printer to a 100% scale. · We recommend using a notcher on the undercloak to avoid splits All dimensions are indicative unless specified on the drawing

Open the catalog to page 11

Double lock standing seam - Guide to detail forming-12

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02a All dimensions are indicative unless specified on the drawing

Open the catalog to page 12

Double lock standing seam - Guide to detail forming-13

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02a All dimensions are indicative unless specified on the drawing

Open the catalog to page 13

Double lock standing seam - Guide to detail forming-14

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02a All dimensions are indicative unless specified on the drawing

Open the catalog to page 14

Double lock standing seam - Guide to detail forming-15

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02b 01 All dimensions are indicative unless specified on the drawing

Open the catalog to page 15

Double lock standing seam - Guide to detail forming-16

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02b 01 For correct printing, please make sure to set your printer to a 100% scale. 8 Cut a smooth curve - no nicks · We recommend using a notcher on the undercloak to avoid splits All dimensions are indicative unless specified on the drawing

Open the catalog to page 16

Double lock standing seam - Guide to detail forming-17

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02b All dimensions are indicative unless specified on the drawing

Open the catalog to page 17

Double lock standing seam - Guide to detail forming-18

elZinc® Installation Guide: Standing seam Chamfered foot - DLSS I 1.2.1.02b All dimensions are indicative unless specified on the drawing

Open the catalog to page 18

Double lock standing seam - Guide to detail forming-19

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03a 01 · OK > 3º · Decorative ﬁnish but more time consuming detail. · Alternative to DLSS 1.2.1.03b All dimensions are indicative unless specified on the dra

Open the catalog to page 19

Double lock standing seam - Guide to detail forming-20

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03a 01 For correct printing, please make sure to set your printer to a 100% scale. · Make small hole at end of undercloak cut All dimensions are indicative unless specified on the drawing

Open the catalog to page 20

Double lock standing seam - Guide to detail forming-21

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03a All dimensions are indicative unless specified on the drawing

Open the catalog to page 21

Double lock standing seam - Guide to detail forming-22

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03a All dimensions are indicative unless specified on the drawing · Steps 5 & 6: In cold weather warm zinc up before cobbling over

Open the catalog to page 22

Double lock standing seam - Guide to detail forming-23

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03a All dimensions are indicative unless specified on the drawing

Open the catalog to page 23

Double lock standing seam - Guide to detail forming-24

elZinc® Installation Guide: Standing seam Curved foot - DLSS I 1.2.1.03b 01 OK > 3º Decorative ﬁnish but more time consuming detail. Alternative to DLSS 1.2.1.03a Avoids opening of end of seam All dimensions are indicative unless specified on the dr

Open the catalog to page 24

Double lock standing seam - Guide to detail forming

Double lock standing seam - Guide to detail forming

Catalog excerpts

All ASTURIANA DE LAMINADOS catalogs and technical brochures