SOMBRA WALL LED LIGHT Operating Instructions

PRECAUTIONS The SOMBRA series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines, heights and beams. The SOMBRA series is available in modular sand-blasted and anodized aluminium casings with E6C0 finishing. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors with 1, 2or3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color or multi-color...

(1) Engine assembly LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options. (2) Tube assembly Sand-blasted anodized aluminium tube assembly with diameter of 100 mm of different heights for fixing on flat surface or ground.

(3) Beam assembly Sand-blasted anodized aluminium assembly with high-grade PMMA glass optical window and different beams.

The modular wall LED light SOMBRA series consists of the following assemblies: • Engine assembly • Tube assembly • Beam assembly • Wall support assembly The assembling and installation have to be realized by qualified personnel. The SOMBRA has to be assembled and fixed as shown in the drawing below:

a) Insert the connection cable and fix the basic component of the Wall support assembly to the wall by using of 2 fixing screws 6.3x50 with wallplugs. b) Insert the connection cable through the Wall support assembly and basic component of the Tube assembly. c) Fix the basic component of the Tube assembly to the Wall support assembly by using of 3 fixing screws M6x20 with washers. d) Fix the jointed Wall support assembly/basic component of the Tube assembly to the fixed basic component of the Wall support assembly by using of 2 fixing screws M6x12 e) Push the tube to the basic component of the...

Synchronization When more than one light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color RGB light is used only with one of the fixed color of lighting the synchronization is not necessary. CONTROLS Single-color warm white (ENGWW), cool white (ENGWW), red (ENGR), blue (ENGB) or green (ENGG) models. Control by...

Turning on /off Press the momentary switch shortly. Changing the color or mode of lighting When the light is turned-off press the momentary switch for 2 seconds. Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity...

Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control The...

TECHNICAL SPECIFICATIONS Engine assembly Power supply Beam angle Optical window Luminous flux (cool white) Operating temperature Casing Protection Dimensions Weight Tube assembly Material Dimensions Anodized aluminium Ø100 x 95 mm Ø100 x 195 mm Ø100 x 495 mm Ø100 x 795 mm Ø100 x C mm (customized) 0.6 kg (90) 0.9 kg (190) 1.7 kg (490) 2.4 kg (790) Beam assembly Material Dimensions Anodized aluminium and PMMA glass Ø100 x 105 (115) mm Ø100 x 60 (70) mm Ø100 x 7 mm 0.6 kg (106) 0.5 kg (61) 0.2 kg (5) Weight Wall support assembly Material Dimensions Weight Anodized aluminium and PMMA glass 100 x...

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Wall LED light SOMBRA series conform to the following Product Specifications: EMC: EN 55015:2006 + A1:2007 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE-marking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje 138 6221 Dutovlje Slovenija

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...