UFO LSR0120 SURFACE GROUND LED LIGHT Operating Instructions

PRECAUTIONS The UFO series of compact outdoor light with built-in driver is designed to use the latest LED lighting technology. The compact designed casing enables the selection of different beam angles. The UFO series is available in stainless steel casings with high-grade polycarbonate or tempered glass lighting windows. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors by using of high-power LED arrays. The most advanced design with built-in microprocessor enables network connection and simple control of complete groups of single-color or multi-color...

INSTALLATION The compact outdoor LED light UFO series consists of the following components:  Surface Ground LED Light UFO series  3 x fixing screw 6.3x38 with wallplugs  Operating Instructions with Declaration of Conformity and Warranty conditions The UFO has to be installed on a flat surface on the ground. The installation has to be realized by a qualified personnel. Drill the 3 holes for wallplugs and insert the 3 wallplugs to the ground Insert the connection cable Fix and tighten the light body to the wallplugs with 3 screws 6.3x38. Connect the power supply and control wires Note:  Do...

The power supply has to be connected through the main switch (not included) with correct polarity and protected by a fuse (not included). The power supply voltage range has to be from 10 - 30 Vdc. Note: • The power supply has to be switched off before installation. The light engine has to be connected as described in the table below: For basic control of the light the CONTROL wire has to be connected through the momentary switch (not included) to the GND by using a 2-pole signal cable extension. (not included) For DMX512 control optional LXU01 or LXU03 interface can be connected to the CONTROL...

Single-color warm white (WW), cool white (CW), red (R), blue (B) or green (G) models. Control by momentary switch Remote control by momentary switch can be used to turn-on and turn-off the light and to control the luminosity. Turning on / off Press the momentary switch momentary. Dimming When the light is on, press the momentary switch longer until the desired power is achieved. Turning on minimum When the light is off, press the momentary switch longer (e.g. one second or more) until the light is turned on at minimum power. Set default Press the momentary switch for min. 40 seconds or until...

Setting the Custom Color At the selected Rainbow Color Spectrum mode press the momentary switch shortly to turn the light off. After that press the momentary switch for 5 seconds or until the light is switched to the selected color and then the Custom Color is set and selected. Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control The...

Dimming When the light is turned-on press the momentary switch until the desired illumination is achieved. By another pressing of the momentary switch the luminosity will increase to the maximum illumination. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control The built-in ASTEL protocol enables the network connection to control the lights with the standard DMX512 protocol by using optional LXU01 or LXU03 interfaces. TECHNICAL SPECIFICATIONS Power supply 12 – 24 Vdc, max. 260 mA/12 Vdc or 135 mA/24 Vdc (1 LED) 12 – 24 Vdc, max. 600 mA/12...

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Surface Ground LED light UFO series conform to the following Product Specifications: EMC: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje...