Path LED Light SPARK
16Pages

SPARK PATH LED LIGHT Operating Instructions

PRECAUTIONS The SPARK series of modular outdoor light with built-in driver is designed to use the latest LED lighting technology. The modular designed casing enables the selection of different light engines, heights and beams. The SPARK series is available in modular sand-blasted and anodized aluminium casings with E6C0 finishing. The lighting is available in cool white, warm white, red, green, blue, RGB or RGBW colors with 1, 2or3 high-power LEDs. The most advanced engine with built-in microprocessor enables network connection and simple control of complete groups of single-color or...

(1) Engine assembly LED lighting assembly built-in sand-blasted anodized aluminium casing with different lighting color, power and beam options. (2) Tube assembly Sand-blasted anodized aluminium tube assembly with diameter of 100 mm of different heights for fixing on flat surface or ground.

(3) Beam assembly Sand-blasted anodized aluminium assembly with high-grade PMMA glass optical window and different beams. The modular path LED light SPARK series consists of the following assemblies: • Engine assembly • Tube assembly • Beam assembly

The assembling and installation have to be realized by qualified personnel. The SPARK has to be assembled and fixed as shown in the drawing below: a) Insert the connection cable and fix the basic component of the Tube assembly to the prepared flat surface or ground by using of 3 fixing screws M8x60 with wallplugs. b) Push the tube to the basic component of the Tube assembly and fix it with 3 enclosed screws M5 c) Connect the power supply and control wires d) Tighten the Engine assembly to the Beam assembly e) Tighten the jointed Engine assembly/Beam assembly to the fixed Tube assembly Note:...

The power supply has to be connected through the main switch (not included) with correct polarity and protected by a fuse (not included). The power supply voltage range has to be from 10 - 30 Vdc. Note: • The power supply has to be switched off before installation. The light engine has to be connected as described in the table below: For basic control of the light the CONTROL wire has to be connected through the momentary switch (not included) to the GND by using a 2-pole signal cable extension. (not included) For DMX512 control optional LXU01 or LXU03 interface can be connected to the...

Dimming When the light is on, press the momentary switch longer until the desired power is achieved. Turning on minimum When the light is off, press the momentary switch longer (e.g. one second or more) until the light is turned on at minimum power. Set default Press the momentary switch for min. 40 seconds or until the light is turned off. DMX512 control The network connection to control the light with the standard DMX512 protocol is enabled by using optional LXU01 or LXU03 interfaces. Multi-color (ENGRGB) model: Control by momentary switch Remote control by momentary switch has to be used...

DMX512 control The built-in ASTEL protocol enables the network connection to control the lights with the standard DMX512 protocol by using optional LXU01 or LXU03 interfaces. Multi-color (ENGRGBW) model: Control by momentary switch Remote control by momentary switch has to be used to turn-on and turn-off the light and to control the mode of lighting and luminosity. When the light is turned-off the color or mode of lighting can be changed sequentially by pressing the momentary switch for 2 seconds: ENGRGBW Sequence of lighting Custom Color _Full RGB_ _Cool White_ _Bluish White_ _Red_ _Green_...

Engine assembly Power supply Beam angle Optical window Luminous flux (cool white) Operating temperature Casing Protection Dimensions Weight Tube assembly Material Dimensions Beam assembly Material Dimensions Design and specifications subject to change without notice.

Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Path LED light SPARK series conform to the following Product Specifications: EMC: EN 55015:2006 + A1:2007 Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CE-marking accordingly: - the EMC Directive 2004/108/EC - the Low Voltage Directive 2006/95/EC ASTEL d.o.o. Dutovlje 138 6221 Dutovlje Slovenija

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written...