UNDERWATER POOL LIGHT Operating Instructions

PRECAUTIONS The METEOR LSR1280 series of a compact ultra-thin underwater pool light with built-in driver is designed to use the latest LED lighting technology. The surface-mount designed casing enable very simple installation on the flat surface without any surface preparation during construction and the max. diameter of the hole through the wall is 8 mm. The METEOR LSR1280 series is available in stainless steel casings. The lighting is available in white, blue, green, RGB, WGB or RGBW colors with 12 high-power LEDs. The multi-color RGB, WGB or RGBW versions allow changing of the color of lighting...

(1) Optical window High-grade polycarbonate glass optical window. (2) Underwater pool light casing Stainless steel casing with fixing holes and cable gland. (3) Cable The 4-pole multi-core cable to connect the 12-24Vdc power supply and optional remote control or switch. (4) Fixing screw The fixing screws to fix the underwater pool light on the wall.

INSTALLATION The underwater light kit consists of the following components: • Underwater Light METEOR LSR1280 • 4 x fixing screw 5.5x50 with wallplugs • Operating Instructions with Declaration of Conformity and Warranty conditions The METEOR LSR1280 has to be installed on a flat surface on the pool wall under water line. Do not try to install the underwater pool light while the pool is filled with water. When the installation is finished briefly test the underwater light prior to fill the pool with water. The installation have to be realized by a qualified personnel. Note: • Avoid using the underwater...

Note: • Do not overtighten the screws as this can result in underwater pool light damage. Earthing The underwater pool light has to be earthed by using a pre-tinned green wire with a yellow stripe a minimum of 8 AWG (8.36 mm2). The wire has to be connected to the underwater pool light by the help of one fixing screw 5.5x50. Connection The power supply has to be connected through the main switch (not included) with correct polarity and protected by a fuse (not included). The power supply voltage has to be from 10 - 30Vdc. Note: • The power supply has to be switched off before installation. The...

Single-color cool white (W), warm white (WW), blue (B) or green (G) models Remote control can be used to turn-on and turn-off the underwater pool light and to control the luminosity. Dimming The dimming are enabled by using optional PWM dimmer LDU13. DMX512 control The network connection to control the lights with the standard DMX512 protocol is enabled by using optional PWM dimmer LDU13 and optional LXU01 interface. Multi-color RGB (M), WGB (WM), RGBW (MW) models: Remote control has to be used to turn-on and turn-off the underwater pool light and to control the mode of lighting and luminosity....

Synchronization When more than one multi-color underwater pool light is connected to the system the optional Synchronization Unit LSU08 is recommended to synchronize the colors of lighting at the Rainbow Color Spectrum mode of lighting. On the other case the colors of all installed lights would not be the same after few minutes or hours of operation in the Rainbow Color Spectrum mode. If the multi-color light is used only with one of the fixed color of lighting the synchronization is not necessary. DMX512 control The built-in ASTEL protocol enables the network connection to control the lights...

TECHNICAL SPECIFICATIONS Power supply Lens angle Optical window Luminous flux ASTEL protocol default address Operating temperature Casing Protection Dimensions Weight 12 - 24 Vdc, max. 1.4 A/12 Vdc or 650 mA/24 Vdc 60° (standard) High-grade polycarbonate glass max. 1.900 lm 1 -10°C - +50°C Stainless steel (316L) IP 68 0119 x 10 mm 0.6 kg Design and specifications subject to change without notice.

WARRANTY 1. The equipment manufactured by ASTEL d.o.o. is warranted to be free from defects in workmanship and materials under normal use and service. 2. This Warranty is in effect for of two years from the date of purchase by the user. Proof of purchase must be included, to establish that it is inside the warranty period. 3. This Warranty is transferrable and covers the product for the specified time period. 4. In case any part od the equipment proves to be defective, other than those parts excluded in paragraph 5 below, the owner should do the following: (a) prepare a detailed written statement...

DECLARATION OF CONFORMITY according to IEC Guide 22 and EN 45014 Manufacturer's Name: ASTEL, Podjetje za projektiranje, proizvodnjo in trgovino, d.o.o. Manufacturer's Address: Dutovlje 138 6221 Dutovlje Slovenija declares that the products Item, Product Name and Model Number: 1. Underwater Pool Light METEOR LSR1280 conform to the following Product Specifications: EMC: Supplementary Information: The products herewith comply with the requirements of the following Directives and carry the CEmarking accordingly: -the Low Voltage Directive 2014/35/EU -the EMC Directive 2014/30/EU -the RoHS Directive...